I2S Audio Breakout – MAX98357A 音頻轉模擬信號模組 SparkFun原廠
NT$238 NT$220 未稅
尚有庫存
- 商品說明
商品說明
I2S Audio Breakout – MAX98357A 音頻轉模擬信號模組
SparkFun I 2 S音頻分線板使用MAX98357A數模轉換器(DAC),可將I 2 S(不與I 2 C 混淆)音頻轉換為模擬信號以驅動揚聲器。I 2 S音頻突破將使用I 2 S標準的數字音頻信號轉換為模擬信號,並使用D類放大器放大信號,該放大器可為4Ω負載提供高達3.2W的功率。電路板可配置為僅輸出左聲道音頻,右聲道或兩者。
SparkFun I 2 S音頻分線板相當簡單,只需幾個引腳連接即可啟動和工作。默認情況下,電路板配置為“單聲道”操作,這意味著左右信號組合在一起以驅動單個揚聲器。如果您需要為左右音頻通道設置單獨的揚聲器,則需要切斷單聲道跳線。除了能夠選擇音頻通道輸出之外,還可以通過幾種方式配置增益。放大器的增益可以配置為低至+ 3dB至高達+ 15dB。雖然可以在板上配置通道選擇,但是可以使用增益引腳在外部控制增益。默認情況下,電路板配置為+ 9dB,但可以輕鬆更改!
規格
- 電源電壓範圍:2.5V – 5.5V。
- 輸出功率:在5V時為3.2W至4Ω。
- 輸出通道選擇:左,右或左/ 2 +右/ 2(默認)。
- 採樣率:8kHz – 96kHz。
- 樣本分辨率:16/32位。
- 靜態電流:2.4mA。
- 無濾波D類輸出
- 不需要MCLK
- 點擊和彈出縮小
- 短路和熱保護。
Documents
=========================================================
SparkFun I2S Audio Breakout – MAX98357A
The SparkFun I2S Audio Breakout board uses the MAX98357A digital to analog converter (DAC), which converts I2S (not be confused with I2C) audio to an analog signal to drive speakers. The I2S Audio Breakout converts the digital audio signals using the I2S standard to an analog signal and amplifies the signal using a class D amplifier which can deliver up to 3.2W of power into a 4Ω load. The board can be configured to output only the left channel audio, right channel, or both.
The SparkFun I2S Audio Breakout board is fairly simple, requiring only a few pin connections to get it up and working. By default the board is configured in “mono” operation, meaning the left and right signals are combined together to drive a single speaker. If you want a separate speaker for the left and right audio channels you’ll need to cut the mono jumper. In addition to being able to select the audio channel output, the gain can also be configured in a few ways. The gain of the amplifier can be configured from as low as +3dB to as high as +15dB. While the channel selection can be configured on board, the gain however is controlled externally using the gain pin. By default, the board is configured for +9dB, but can be easily changed!
FEATURES
- Supply Voltage Range: 2.5V – 5.5V.
- Output Power: 3.2W into 4Ω at 5V.
- Output Channel Selection: Left, Right, or Left/2 + Right/2 (Default).
- Sample Rate: 8kHz – 96kHz.
- Sample Resolution: 16/32 bit.
- Quiescent Current: 2.4mA.
- Filterless Class D Outputs
- No MCLK Required
- Click and Pop Reduction
- Short-Circuit and Thermal Protection.
Documents
- wiki
- Schematic
- Eagle Files
- Hookup Guide
- Datasheet (MAX98357A)
- GitHub
相關商品
-
加入購物車Quick View
Grove – Rotary Angle Sensor 旋轉角度電位器模組 seeed原廠
0 滿分 5 分加入購物車Quick View -
加入購物車Quick View
HC-05 串口藍牙模組 (帶底板) 主機/從機可設定 / 帶底板,附 Arduino 範例
0 滿分 5 分請勿將電源接到信號腳上,會直接燒壞模組!
藍牙透傳模組只有4個AT指令,分別是測試通訊,改名稱,改串列傳輸速率,改配對密碼,AT指令必須從TXD,RXD信號腳設置,不能通過藍牙通道設置。發送AT指令的設備可以是各種類型的MCU(比如51,avr,pic,msp430,arm等),也可以是電腦通過串口(PC串口接MAX232以後或者USB轉串口)發送。
加入購物車Quick View -
加入購物車Quick View
2路電平轉換模組帶隔離 2-Channel Level Converter (12V to 5V) DFRobot原廠
0 滿分 5 分加入購物車Quick View -
Grove – Infrared Temperature Sensor 紅外線 溫度感測器模組 seeed原廠
0 滿分 5 分紅外溫度傳感器通過接收物體發出的紅外線來測量其溫度。
NT$457NT$380 未稅加入購物車Quick View -
TF Mini LiDAR 12m (ToF) 雷射 激光 距離測量傳感器/感測器 DFRobot原廠
0 滿分 5 分TF Mini LiDAR是一款基於飛行時間(ToF)技術的單向激光測距儀。
它由特殊的光學和電子設備組成,集成了適用於室內和室外應用環境的自適應算法。
它具有纖巧的機身和遠距離測量的高性能。
NT$1,600NT$1,420 未稅加入購物車Quick View -
加入購物車Quick View
單片機TTL轉RS485模組 485轉串口UART電平互轉 硬體自動控制流向
0 滿分 5 分加入購物車Quick View -
Grove – Relay 繼電器模組 ( 峰值電壓能力250V 10安培) 支援 Arduino 與 Raspberry Pi seeed原廠
0 滿分 5 分繼電器是數位電路常用的控制開關元件,可用於控制更高的電壓和電流。設置為高電位時,指示燈會亮,繼電器ON。
NT$143NT$120 未稅加入購物車Quick View -
加入購物車Quick View
Grove – Multichannel Gas Sensor v2 多通道有害氣體感測器 seeed原廠
0 滿分 5 分加入購物車Quick View -
Grove – I2C Touch Sensor 電容式觸摸感測器 I2C 觸摸開關感應器 seeed原廠
0 滿分 5 分I2C 觸摸感測器使用飛思卡爾MPR121晶片,它可以感應觸碰和人的手指的接近。這個感應器包括兩部分——一個觸碰感應控制器和4個感應片。把感應片插到控制器上,就可以開始使用了。
NT$819NT$400 未稅加入購物車Quick View -
Analog pH Meter Pro Sensor 模擬檢測 PH值(專業版) 相容Arduino DFRobot原廠
0 滿分 5 分NT$2,667NT$2,460 未稅加入購物車Quick View