I2C Digital Wattmeter 數位功率計 電壓、電流、功率、三合一大量程 DFRobot原廠
NT$314 NT$280 未稅
Gravity:I2C數字功率計是一款可測量26V 8A以內各類電子模塊、用電設備的電壓、電流和功率,最大相對誤差不超過±0.2%的高分辨、高精度、大量程測量模塊(使用前需進行一次簡單的手動校準)。可用於太陽能係統、電池庫侖計、電機、主控板或電子模塊的功耗測量、電池續航評估與實時電源參數在線監控。
尚有庫存
- 商品說明
商品說明
I2C Digital Wattmeter 數位功率計 電壓、電流、功率、三合一大量程
Gravity:I2C數字功率計是一款可測量26V 8A以內各類電子模塊、用電設備的電壓、電流和功率,最大相對誤差不超過±0.2%的高分辨、高精度、大量程測量模塊(使用前需進行一次簡單的手動校準)。可用於太陽能係統、電池庫侖計、電機、主控板或電子模塊的功耗測量、電池續航評估與實時電源參數在線監控。模塊採用TI INA219零溫漂電流/功率監控芯片和2W大功率低溫漂10mΩ合金采樣電阻,電壓和電流分辨率分別可達4mV與1mA,在滿量程測量條件下,電壓與電流的最大測量相對誤差不超過±0.2%,並提供4個可通過撥碼開關配置的I2C地址。模塊可對雙向高側電流(流經電源或電池正極的電流)進行準確測量,這在太陽能或庫侖計應用,電池既需要充電,也需要放電的場合尤為有用,用戶可通過電流的正負讀數了解電池的充放電狀態,也可以了解電池的衝放電的實時電壓、電流與功率。在電機應用場景,可通過實時監控電機電流是否由於堵轉或負載過大導致電流過大,從而及時採取保護措施。此外,也可以使用該模塊測量各類電子模塊或整個項目的實時功耗,從而評估電池的續航時間。
接口說明
|
|
連線圖
Gravity: I2C Digital Wattmeter 連接圖(Arduino UNO)
應用實例
監測太陽能係統中太陽能板、電池與輸出的功耗情況
特徵
- 高精度、高分辨率、大量程、低溫漂
- 雙向電流高側測量
- 兼容3.3V/5V控制器
- 精緻小巧,方便項目嵌入
應用領域
- 太陽能係統
- 電池庫侖計
- 電子模塊功耗評估
規格
- 供電電壓(VCC):3.3V ~ 5.5V
- 電壓量程(IN+或IN-相對GND):0 ~ 26V
- 電壓分辨率:4 mV
- 電壓相對誤差:<±0.2%(典型值)
- 電流量程:0 ~ ±8A(可測雙向電流)
- 電流分辨率:1 mA
- 電流相對誤差:<±0.2%(典型值,需手動校準)
- 功率量程:0 ~ 206 W
- 功率分辨率:20 mW(硬件)/4mW(軟件)
- 靜態電流:0.7 mA
- 通信接口:Gravity I2C (邏輯電平0-3.3V)
- I2C地址:4個,0x40,0x41,0x44,0x45(默認)
- 產品尺寸:30.0mm×22.0mm
- 重量:4g
出貨清單
- Gravity:I2C數字功率計 x1
- XH2.54-4P黑色直單排針 x1
- Gravity-4P傳感器連接線 x1
Documents
=========================================================
Gravity: I2C Digital Wattmeter
Gravity: I2C Digital Wattmeter is a high-resolution, high-precision, large-scale measurement module that can measure the voltage, current and power of various electronic modules and electrical equipment within 26V 8A, and the maximum relative error is no more than ±0.2% (A simple manual calibration is required before usage). It can be used for power consumption or battery life evaluation of solar energy systems, battery, motors, controller or electronic modules.
The module adopts TI INA219 zero temperature drift current/power monitoring chip and 2W high power low temperature drift 10mΩ alloy sampling resistor. The voltage and current resolution can reach 4mV and 1mA respectively. Under the full scale measurement condition, the maximum relative error of voltage and current measurement can be superior to ±0.2%. It also provides four I2C addresses that can be configured via the 2P DIP switch. The module accurately measures bi-directional high-side currents (current flowing through the power supply or battery positive), which is especially useful in solar or battery fuel gauge applications where the battery needs to be charged and discharged. This status can be simply determined by positive or negative current readings. In the motor applications, the current can be monitored in real time by monitoring whether the motor current is too large due to overload. In addition, you can use this module to measure the power consumption of various electronic modules or the entire project to evaluate battery life.
CONNECTION DIAGRAM
Gravity: I2C Digital Wattmeter Connection Diagram (Arduino UNO)
Gravity: I2C Digital Wattmeter Connection Diagram (Raspberry Pi 3B)
Measuring the power consumption of the Gravity: pH meter
Monitor the power consumption of the solar panel, battery and outputs of a solar system
FEATURES
- High precision, high resolution, large range, low temperature drift
- Bidirectional current high side measurement
- Compatible with 3.3V/5V controller
- Sophisticated and compact, easy to embed in the project
APPLICATIONS
- Solar Power Management
- Battery Fuel Gauge
- Electronic Module Power Evaluation
SPECIFICATION
- Input Voltage (VCC) : 3.3V~5.5V
- Voltage Range (IN+ or IN- relative to GND): 0 ~ 26 V
- Voltage Resolution: 4 mV
- Voltage Relative Error: <±0.2% (Typical)
- Current Range: 0 ~ ±8A (Bidirectional current)
- Current Resolution: 1mA
- Current Relative Error: <±0.2% (Typical, manual calibration required)
- Power Range: 0 ~ 206 W
- Power Resolution: 20 mW (Hardware) / 4 mW (Software)
- Quiescent Current: 0.7 mA
- Interface: Gravity I2C (logic level: 0-3.3V)
- I2C Address: Four options 0x40, 0x41, 0x44, 0x45
- Dimension: 30.0mm*22.0mm/1.18*0.87 in
- Weight: 4g
DOCUMENTS
SHIPPING LIST
- Gravity: I2C Digital Wattmeter x1
- XH2.54-4P Black Header x1
- Gravity-4P I2C/UART Sensor Wire x1
相關商品
-
Grove – PIR Motion Sensor 紅外線人體移動探測感測器 seeed原廠
0 滿分 5 分這是一個極易使用的紅外線 PIR人體運動探測感測器。通過這個感測器,你可以使你的作品對運動,例如人類的運動作出互動。只要將其接到Grove – Base Shield上,並且下載程序,當有人走入它的探測範圍時,PIR運動探測傳感器就會在它的SIG腳上輸出一個HIGH信號。
NT$333NT$260 未稅加入購物車Quick View -
Grove – Serial Camera Kit 串列通訊攝影機鏡頭套件 seeed原廠
0 滿分 5 分本套件中提供了兩種規格的鏡頭。標準配置用於普通照片拍攝,廣角拍攝特別適用於監控項目。
加入購物車Quick View -
電子元件入門學習套件組 Keyes 初學者入門學習套件 20堂課程 教學 套件
0 滿分 5 分電子元件入門 初學者學習套件組 ,套件包含各色LED 、電阻、電容、數碼管等常用電子小元件和麵包板,不包含 開發板。原件清單比較齊全,適合愛好電子的初學者使用。本套件的全部資料都是以 UNO R3 作為控制板,學習者使用其他型號的開發板,可以上網自行查找相關資料,也可以參考我們提供的資料作一定的修改。
NT$856NT$600 未稅加入購物車Quick View -
9V 電池扣 轉 DC 電源插頭 / 9V 電池連接線 for Arduino
0 滿分 5 分Arduino互動媒體、 32路舵機控制器必備器材,DC插頭內正外負。
9V 電池連接線 for Arduino
NT$19NT$14 未稅加入購物車Quick View -
Grove – Vibration Motor 振動馬達 直流馬達模組 seeed原廠
0 滿分 5 分這是一款無聲的迷你震動馬達模組。當輸入高電平時,電機會像手機在靜音模式一樣振動。支援 Arduino 與 Raspberry Pi
NT$114NT$100 未稅加入購物車Quick View -
Grove – 4-Digit Display 4位LED 數位顯示模組 seeed原廠
0 滿分 5 分NT$238NT$160 未稅加入購物車Quick View -
Grove – Flame Sensor 火焰感測器 seeed原廠
0 滿分 5 分NT$371NT$200 未稅加入購物車Quick View -
加入購物車Quick View
MEGA 2560 R3 副廠開發板 ATMega16U2 採用原廠晶片 通過美國FCC認證 送1.3m長傳輸線
0 滿分 5 分採用全新原廠晶片及國際標準環保材質生產製造,通過美國FCC認證
加入購物車Quick View -
Grove – UART WiFi V2 無線網路模組 / 串口通訊模組 ESP8285 晶片
0 滿分 5 分Grove UART WiFi ESP8285 是一個串行無線網路收發器模組,具有無所不在的物聯網 ESP8285的SoC。
NT$524NT$420 未稅加入購物車Quick View -
Grove – GPS Module 衛星模組 適用於 Arduino 與 Raspberry Pi seeed原廠
0 滿分 5 分Grove – GPS模組是一款低成本及可程式設計的GPS模組,可用於手持設備GPS資料的採集。模組採用串口通信,可通過串口進行資料的讀取。它設有一個50通道的u-blox 5定位引擎,首次定位時間(TTFF)小於1s。跟蹤和採集的靈敏度均達到-160dBm,適用於個人導航及位置服務的專案。
NT$857NT$700 未稅加入購物車Quick View