





溶解氧感測器 V2 溶解氧含量 水電導率感測器 液體檢測 水質監測 相容Arduino Gravity
NT$3,143 NT$2,619 未稅
Gravity:模擬電導率計V2專門用於測量水溶液的電導率值,評估水質狀況,常用於水培、水產養殖、環境水檢測等領域。
產品配合主控板(如Arduino)與配套的軟件庫,就可迅速搭建出一套電導率檢測儀,即插即用,無需焊接。
尚有庫存
- 商品說明
商品說明
Arduino Gravity: 溶解氧感測器 V2 溶解氧含量 水電導率感測器 液體檢測 水質監測 相容Arduino
溶解氧感測器 V2 專門用於測量水溶液的電導率 。評估水質狀況,常用於水培、水產養殖、環境水檢測等領域。V2電導率儀為V1的升級版,大大提高了用戶體驗和數據精度。它支持3~5v寬電壓輸入,並兼容5V和3.3V主控板; 由硬件濾波的輸出信號具有低抖動; 激勵源採用交流信號,有效降低極化效應,提高精度,延長探頭壽命; 該軟件庫採用兩點校準方法,可以自動識別標準緩衝解決方案,因此簡單方便。
有了這個產品,主控板(如Arduino)和軟件庫,可以快速建立電導率儀,即插即用,無需焊接。DFRobot提供各種水質傳感器產品,尺寸與接口統一,滿足各類水質檢測的需求,也適合搭建多參數水質檢測儀。
電導率是電阻率的倒數,與物質傳送電流能力的大小有關,在液體中常以電阻的倒數電導來衡量其導電能力的大小。水的電導是衡量水質的一個重要指標,它能反映出水中存在的電解質的程度。
- 本產品配套的電極為實驗室級電極,請勿長時間放在液體中測量,否則會縮短電極的使用壽命。
- 本產品配套的電極的鉑金片表面附著有鉑黑層,應避免任何物體與其觸碰,只能用蒸餾水沖洗,否則會損傷鉑黑層,導致電極測量不准確。
接線圖
注意:
特徵
- 3.0~5.0V寬電壓輸入
- 硬件濾波輸出信號,低抖動
- 交流激勵源,有效減少極化
- 重力連接器和BNC連接器,即插即用,無需焊接
- 軟件庫支持兩點校準,並自動識別標準緩衝解決方案,集成溫度補償算法
- 尺寸和連接器尺寸均勻,便於機械結構設計
應用
- 水質監測。
- 水產養殖。
- 水培和Aquaponic。
規格參數
- 信號轉換板(發射器)V2:
- 供電電壓:3.0~5.0V
- 輸出電壓:0~3.4V
- 電極接口:BNC
- 信號接口:PH2.0-3Pin
- 測量精度:±5% FS
- 板子尺寸:42mm*32mm
- 電導率電極:
- 電極類型:實驗室級電極
- 電極常數:1.0
- 支持檢測範圍:0~20ms/cm
- 推薦檢測範圍:1~15ms/cm
- 溫度範圍:0~40℃
- 電極壽命:>0.5年(實際壽命與使用頻率、場景有關)
- 線纜長度:100cm
出貨清單
- 電導率探頭(K = 1,實驗室級)x1
- 信號轉換板(發射器)V2 x1
- 標準緩衝溶液1413us / cm x2
- 標準緩衝溶液12.88ms / cm x2
- 重力模擬傳感器連接線 x1
- 防水墊片x2
- BNC連接器x1的螺帽
- M3 * 10尼龍柱x4
- M3 * 5螺絲x8
Documents
=========================================================
Gravity: Analog Electrical Conductivity Sensor /Meter V2 (K=1)
DFRobot Gravity: analog electrical conductivity meter V2 is specially used to measure the electrical conductivity of aqueous solution, and then to evaluate the water quality, which is often used in water culture, aquaculture, environmental water detectionand other fields. You may also check Liquid Sensor Selection Guide to get better familar with our liquid sensor series.
This product, as an upgraded version of electrical conductivity meter V1, greatly improves the user experience and data precision. It supports 3~5v wide voltage input, and is compatible with 5V and 3.3V main control board; The output signal filtered by hardware has low jitters; The excitation source adopts AC signal, which effectively reduces the polarization effect, improves the precision and prolongs the life of the probe; The software library uses two-point calibration method, and can automatically identify standard buffer solution, so simple and convenient.
With this product, main control board (such as Arduino) and the software library, you can quickly build an electrical conductivity meter, plug and play, no welding. DFRobot provides a variety of water quality sensor products, uniform size and interface, not only meet the needs of various water quality testing, but also suitable for the DIY of multi-parameter water quality tester.
Conductivity is the reciprocal of the resistance, which is related to the ability of the material to carry the current. In the liquid, the reciprocal of the resistance, the conductivity, is the measure of its ability to conduct electricity. Conductivity is an important parameter of water quality. It can reflect the extent of electrolytes present in water.
In order to ensure the measurement accuracy, it is strongly recommended to add a temperature sensor to measure the temperature, and achieve automatic temperature compensation. DS18B20 waterproof temperature sensor can also be used.
1.The probe is a laboratory-grade probe. Do not immerse in liquid for a long time. Otherwise this will shorten the life of the probe.
2.Platinum black layer is attached to the surface of the sheet metal in the probe.It should avoid any object touching it. It can only be washed with distilled water, otherwise the platinum black layer will be damaged, resulting in inaccurate measurement.
FEATURES
- 3.0~5.0V wide voltage input
- Hardware filtered output signal, low jitter
- AC excitation source, effectively reduce polarization
- Gravity connector and BNC connector, plug and play, no welding
- Software library supports two-point calibration, and automatically identifies standard buffer solution, integrates temperature compensation algorithm
- Uniform size and connector, convenient for the design of mechanical structures
APPLICATIONS
- Water quality monitoring.
- Aquaculture.
- Hydroponic & Aquaponic.
SPECIFICATION
Signal Conversion Board (Transmitter) V2
- Supply Voltage: 3.0~5.0V
- Output Voltage: 0~3.4V
- Probe Connector: BNC
- Signal Connector: PH2.0-3Pin
- Measurement Accuracy: ±5% F.S.
- Board size: 42mm*32mm/1.65in*1.26in
Electrical Conductivity Probe
- Probe Type: Laboratory Grade
- Cell Constant: 1.0
- Support Detection Range: 0~20ms/cm
- Recommended Detection Range: 1~15ms/cm
- Temperature Range: 0~40°C
- Probe Life: >0.5 year (depending on frequency of use)
- Cable Length: 100cm
DOCUMENTS
SHIPPING LIST
- Electrical Conductivity Probe(K=1,Laboratory Grade) x1
- Signal Conversion Board (Transmitter) V2 x1
- Standard Buffer Solution 1413us/cm x2
- Standard Buffer Solution 12.88ms/cm x2
- Gravity Analog Sensor Cable x1
- Waterproof Gasket x2
- Screw Cap for BNC Connector x1
- M3 * 10 nylon pillar x4
- M3 * 5 screw x8
相關商品
-
感測器37件組 | 入門感測器學習Arduino教學套件/詳細Arduino Sensor 入門教材資料
0 滿分 5 分感測器37件組 | 感測器入門學習Arduino套件 |滿滿 2.4G 1CD 入門教材資料
最佳的感測器入門學習Arduino套件,讓您幾分鐘之內快速上手,不需四處奔波搜尋各種教學資料, 直接給給你最齊全的感測器零件組合與教學課程與範例程式,立刻體驗豐富有趣的Arduino創作世界。這款入門套件收錄了 Arduino 初學者最常應用到的感測器零件,以及介紹這 37 種感測器的使用教學與程式範例。
NT$1,333NT$1,143 未稅加入購物車速覽 -
UNO ABS 工控專用機殼可壁掛
0 滿分 5 分UNO ABS 機殼 兼容市面上UNO R3 系列主板,包括官方義大利正廠,副廠的,統統兼容,免鎖螺絲!
可視性強各接口均有對應開口設置,非一般市面上常見的易碎壓克力殼
NT$238NT$114 未稅加入購物車速覽 -
MCU-arduino CP2102 模組 USB 轉TTL USB轉串口 UART STC下載器
0 滿分 5 分NT$114NT$86 未稅加入購物車速覽 -
Sensor Shield V5.0 感測器擴展板 支援Arduino單機片
0 滿分 5 分最新推出的Sensor Shield V5.0 感測器擴展板,採用疊層設計,主板不僅將 Arduino Uno 的全部 Digital 與 Ananog pins 擴展出來,還特設 IIC 接口、舵機控制器接口、藍芽模組通信接口、SD 卡模組通信接口、APC220 無線射頻模組通信接口、超聲波感測器接口、12864液晶串列與並行接口,獨立擴出更加易用方便。對於 Arduino 初學者來說,不必為繁瑣複雜電路連線而頭疼了,這款感測器擴展板真正意義上的將電路簡化,能夠很容易地將常用感測器連接起來,一款感測器僅需要一種通用3P感測器連接線(不分數字連接線與模擬連接線),完成電路連接後,編寫相應的Arduino程序下載到Arduino 控制器中讀取感測器數據、或者接收無線模組回傳數據,經過運算處理,最終輕鬆完成你自己的互動作品。
NT$124NT$86 未稅加入購物車速覽 -
Motor Pack 舵機工具包 for Arduino seeed原廠
0 滿分 5 分NT$667NT$571 未稅加入購物車速覽 -
Water Sensor 水位感測器
0 滿分 5 分Water Sensor水位感測器是一款簡單易用、性價比較高的水位/水滴識別檢測傳感器,其是通過具有一系列的暴露的平行導線線跡測量其水滴/水量大小從而判斷水位。輕松完成水量到模擬信號的轉換,輸出的模擬值可以直接被Arduino開發板讀取,達到水位報警的功效。
NT$48NT$38 未稅加入購物車速覽 -
CP2102 多功能串口轉換模組 USB 轉 TTL,RS485,RS232互轉 支援3.3V/5V 切換,支援Win 7/8/10
0 滿分 5 分CP2102 多功能串口轉換模組 USB 轉 TTL,RS485,RS232互轉 支援3.3V/5V 切換
全面支持Win8,Win7,WinXp, Win2K,WinCE,Linux,Mac,系統,32位、64位系統,最新驅動全面支持
出廠時撥碼開關已撥到全ON位置,經過測試能夠適應所有模式
NT$238NT$171 未稅加入購物車速覽 -
Gravity: 錐形模擬 PH值 感測器 傳感器 (測量土壤與食物的PH值) DFRobot原廠
0 滿分 5 分對於土壤、食物這類半固體物質,普通pH電極不可直接測量,不然容易導致電極異常甚至損壞。
該產品的pH電極帶有不銹鋼針刺護套,可直接刺入半固體物質,因此可方便的測量濕潤土壤、食物(如肉類、水果)等物質的pH值,這是普通pH電極不能達到的。
本產品兼容Arduino,即插即用,簡單方便,可快速DIY一個pH檢測儀,直接測量土壤或食物的pH值。NT$4,000NT$3,790 未稅加入購物車速覽 -
Gravity: Analog Turbidity Sensor 水濁度感測器 水質檢測 養殖環境監測 For Arduino DFRobot原廠
0 滿分 5 分濁度感測器利用光學原理,通過測量溶液中的透光率和散射率來綜合判斷溶液濁度情況,從而達到檢測水質的目的。
NT$648NT$552 未稅加入購物車速覽 -
G1&8″ Water Flow Sensor 霍爾 水流量感測器 seeed原廠
0 滿分 5 分水流量傳感器主要由塑料閥體、水流轉子組件和霍爾傳感器組成。它裝在熱水器進水端,用於檢測進水流量,當水通過水流轉子組件時,磁性轉子轉動並且轉速隨著流量變化而變化,霍爾傳感器輸出相應脈衝信號,反饋給控制器,由控制器判斷水流量的大小,進行調控。
NT$305NT$257 未稅加入購物車速覽