匯承HC-08 低功耗 BLE CC2540 藍芽模組 4.0 主機/從機一體化 藍牙轉串口
NT$219 – NT$238 未稅
帶底板針腳(附排針需自行焊接)
HC-08 藍芽串口通信模組是新一代的基於Bluetooth Specification V4.0 BLE 藍芽協議的通訊模組。無線工作頻段為2.4GHz ISM,調製方式是GFSK。模組最大發射功率為4dBm,接收靈敏度-93dBm,空曠環境下和iphone4s 可以實現80 米超遠距離通信。模組採用郵票孔封裝方式,可貼片焊接,模組大小26.9mm×13mm×2.2mm,很方便客戶嵌入應用系統之內。
模組採用TI 的CC2540 晶片,配置256K Byte 空間,支援AT 指令,用戶可根據需要更改角色(主、從模式)以及UART串列傳輸速率、設備名稱等參數,使用靈活。
- 商品說明
商品說明
匯承HC-08 低功耗 BLE CC2540 藍芽模組 4.0 主機/從機一體化 藍牙轉串口
HC-08 藍芽串口通信模組是新一代的基於Bluetooth Specification V4.0 BLE 藍芽協議的通訊模組。無線工作頻段為2.4GHz ISM,調製方式是GFSK。模組最大發射功率為4dBm,接收靈敏度-93dBm,空曠環境下和iphone4s 可以實現80 米超遠距離通信。模組採用郵票孔封裝方式,可貼片焊接,模組大小26.9mm×13mm×2.2mm,很方便客戶嵌入應用系統之內。
模組採用TI 的CC2540 晶片,配置256K Byte 空間,支援AT 指令,用戶可根據需要更改角色(主、從模式)以及UART串列傳輸速率、設備名稱等參數,使用靈活。
請注意 使用手機或平板等裝置,要先確認是否有支援藍芽 BLE 4.0
HC-08藍牙模塊4.0 遠距離低功耗ble芯片主從一體無線串口模塊
藍牙4.0 BLE模塊,支持與iPhone4s和安卓4.3以上版本的手機連接,低功耗,傳輸距離為80米。底部帶有排針焊接口,免底板使用,快捷方便!
Wireless Bluetooth TTL Transceiver Module HC-08 CC2540 BLE CSR4.0
HC-08 firmware versions
- The default baud rate is 9600.
- There must be a delay between data packets. For example, if the baud rate is 1200 baud, the packet length is 120 bytes and the transmission time delay between packets must be not less than 2000ms otherwise you may lose data. The packet transmission time delay for 38400 baud with a packet length is 120 bytes must not be less than 200ms. At 115,200 baud with a packet length of 120 bytes, the transmission time delay between data packets must be not less than 50ms).
- When the baud rate is 19200 baud or more, the number o per packet cannot be more than 120 bytes.
- The higher the baud rate, the shorter the transmission delay time required between data packets.
- The shorter the number o per packet, the shorter the required delay time (e.g. 115,200 baud with a packet length of 20 bytes, the transmission delay time between data packets is less than 20ms).
HC-08 Pin Definition
TXD:串口發送,3.3V TTL電平。
RXD:串口接收,3.3V TTL電平。
CTS:串口流控,暫不支持。
RTS:串口流控,暫不支持。
DC:模擬、燒錄時鐘腳。
DD:模擬、燒錄數據腳。
RST:模組重定腳,要求不小於5ms的低電平進行復位。
VCC:模組電源腳,要求直流3.3V電源,供電電流不小於100mA。工作電壓範圍:2.0V~3.6V。
GND:模組公共地。
LED:模組指示燈輸出腳,高電平輸出,接LED時請串接電阻。
連線前,
主機未記錄從機位址時,每秒亮100ms;
主機記錄從機位址時,每秒亮900ms;
從機每2秒亮1秒。
連線後,LED常亮。
KEY:輸入腳,內部下拉。此腳接高電平,用於主機清除已記錄的從機位址。
- Pin 1: (UART TX) serial transmit, 3.3V TTL level.
- Pin 2: (UART RX) serial receive, 3.3V TTL level.
- Pin 3: (CTS) serial flow control, not supported.
- Pin 4: (RTS) serial flow control, not supported.
- Pin 11: (RST) reset pin; take LOW for not less than 5ms.
- Pin 12: (VCC) 2-3.6VDC operating voltage (typical 3.3VDC), current not less than 100mA.
- Pin 13: (VSS) common ground.
- Pin 22: (VSS) common ground.
- Pin 24: (LED) LED output pin; ON when paired/connected, PULSING when not paired/connected.
- Pin 26: (KEY): internal pulldown resistor keeps LOW for normal operation; HIGH erase pairing/connection information; after erasure, searches for new device to pair with/connect to randomly.
HC-08 AT commands
- AT responds OK
- AT + BAUDx responds with OKn where x is 1 – n is 1200, 2 – 2400, 3 – 4800, 4 – 9600 (default), 5 – 19200, 6 – 38400, 7 – 57600, 8 – 115200. Note: module must be reset after power-on for the new serial port baud rate to take effect.
- AT + NAMEname responds OKsetname – name is the Bluetooth device name to be set and must be 13 characters or fewer. Retained across power offs. Note: module must be reset after power-on for the new device name to take effect.
相關商品
-
加入購物車Quick View
JDY-08 帶底板藍牙 4.0 BLE 低功耗 CC2541 模組 支持 Airsync iBeacon
0 滿分 5 分JDY-08 帶底板藍牙 4.0 BLE 低功耗 CC2541 模組 支持 Airsync iBeacon
JDY-08 透傳模組是基於藍牙4.0協議標準,工作頻段為2.4GHZ範圍,調製方式為GFSK,最大發射功率為0db,最大發射距離80米,採用TICC2541晶片設計,支援用戶通過AT命令修改設備名、服務UUID、發射功率、配對密碼等指令,方便快捷使用靈活。
加入購物車Quick View -
加入購物車Quick View
美國官方授權經銷 ARDUINO NANO 33 BLE 義大利製 已焊針腳
0 滿分 5 分加入購物車Quick View -
433 868 915MHz Ultra low power data radio module 低功耗無線數據傳輸模組 內附天線
0 滿分 5 分低功耗無線數據傳輸模組內附天線
加入購物車Quick View -
HC-06 藍芽轉 UART 從機藍芽模組 具底板,提供Arduino 範例
0 滿分 5 分請勿將電源接到信號腳上,會直接燒壞模組!
兼容版跟原裝版的功能操作方法都相同!
加入購物車Quick View -
加入購物車Quick View
HM-10 CC2541 主從一體 藍牙4.0模組 BT4.0 / BLE 帶邏輯電平轉換
0 滿分 5 分加入購物車Quick View -
Grove – UART WiFi V2 無線網路模組 / 串口通訊模組 ESP8285 晶片
0 滿分 5 分Grove UART WiFi ESP8285 是一個串行無線網路收發器模組,具有無所不在的物聯網 ESP8285的SoC。
NT$524NT$420 未稅加入購物車Quick View -
LoPy4 四合一無線IOT開發板模組 兼容Lora/Sigfox/Wi-Fi/藍芽 Pycom 原裝進口
0 滿分 5 分Lopy4結合了四種網絡的開發板 (LoRa,Sigfox,WiFi,藍牙)
NT$2,267NT$2,000 未稅加入購物車Quick View -
Grove – BLE (dual model HM13) 藍牙4.0 模組 CSR雙模藍牙晶片 seeed原廠
0 滿分 5 分Grove – BLE (雙模)使用了CSR 雙模藍牙晶片,該晶片採用了ARM 架構支持AT 指令。用戶可以使用AT 指令靈活的配置串口波特率、設備名字、配對密碼等。
NT$790NT$600 未稅加入購物車Quick View -
RedBear DUO – Wi-Fi + BLE IoT Board 物聯網開發板 seeed原廠
0 滿分 5 分RedBear DUO – Wi-Fi + BLE IoT Board 物聯網開發板
RedBear公司所推出、尺寸只有姆指一般大的Duo開發板,能夠簡化物聯網裝置的開發流程,Duo提供了多種開發者需要的功能,支援Wi-Fi無線網 路、BLE低功耗藍牙等傳輸規範,還能夠支援RBLink擴充子板,讓開發者可以輕鬆擴充各種感應器以及功能模組,嘗試動手打造各種試作品或是成品。
RedBear先前曾推出第一款Arduino用的低功耗藍牙擴充板,過去也推出多款改版產品,在累積了一定IoT領域的經驗之後,RedBear這次推出了自有品牌的Duo開發板。
NT$886NT$790 未稅加入購物車Quick View -
加入購物車Quick View
HC-05 串口藍牙模組 (帶底板) 主機/從機可設定 / 帶底板,附 Arduino 範例
0 滿分 5 分請勿將電源接到信號腳上,會直接燒壞模組!
藍牙透傳模組只有4個AT指令,分別是測試通訊,改名稱,改串列傳輸速率,改配對密碼,AT指令必須從TXD,RXD信號腳設置,不能通過藍牙通道設置。發送AT指令的設備可以是各種類型的MCU(比如51,avr,pic,msp430,arm等),也可以是電腦通過串口(PC串口接MAX232以後或者USB轉串口)發送。
加入購物車Quick View