TB6612FNG Dual Motor Driver 超小設計雙馬達驅動板 CJMCU
NT$214 NT$160 未稅
TB6612FNG Dual Motor Driver 超小設計雙馬達驅動板 CJMCU
TB6612FNG電機驅動模塊小體積高性能超L298N 自平衡小車3PI配套. 該模塊相對於傳統的L298N效率上提高很多,體積上也大幅度減少,在額定範圍內,芯片基本不發熱,當然也就顯得更加嬌貴,所以我們建議有一定動手能力的朋友使用,接線的時候務必細心細心再細心,注意正負極性。
尚有庫存
- 商品說明
商品說明
TB6612FNG Dual Motor Driver 超小設計雙馬達驅動板 CJMCU
TB6612FNG電機驅動模塊小體積高性能超L298N 自平衡小車3PI配套
該模塊相對於傳統的L298N效率上提高很多,體積上也大幅度減少,在額定範圍內,芯片基本不發熱,當然也就顯得更加嬌貴,所以我們建議有一定動手能力的朋友使用,接線的時候務必細心細心再細心,注意正負極性。
Description: The TB6612FNG motor driver can control up to two DC motors at a constant current of 1.2A (3.2A peak). Two input signals (IN1 and IN2) can be used to control the motor in one of four function modes – CW, CCW, short-brake, and stop. The two motor outputs (A and B) can be separately controlled, the speed of each motor is controlled via a PWM input signal with a frequency up to 100kHz. The STBY pin should be pulled high to take the motor out of standby mode.CJMCU.
Logic supply voltage (VCC) can be in the range of 2.7-5.5VDC, while the motor supply (VM) is limited to a maximum voltage of 15VDC. The output current is rated up to 1.2A per channel (or up to 3.2A for a short, single pulse).
Board comes with all components installed as shown. Decoupling capacitors are included on both supply lines. All pins of the TB6612FNG are broken out to two 0.1″ pitch headers ; the pins are arranged such that input pins are on one side and output pins are on the other. Features:
- Power supply voltage: VM=15V max, VCC=2.7-5.5V
- Output current: Iout=1.2A(average) / 3.2A (peak)
- Standby control to save power
- CW/CCW/short brake/stop motor control modes
- Built-in thermal shutdown circuit and low voltage detecting circuit
- All pins of the TB6612FNG broken out to 0.1″ spaced pins
- Filtering capacitors on both supply lines
相關商品
-
機器手臂 專用 交換式電源 25W 5V5A 可同時供應多個舵機
0 滿分 5 分機器手臂專用交換式電源 25W 5V5A 可同時供應多個舵機
提供六軸機械手臂,六顆伺服馬達電源。
使用 105℃ 長壽電解電容, 可操作於環溫 70℃
抗 300VAC 輸入電壓突波, 高達 5 秒之能力
35 – 150W 均通過 EN61000-6-2 重工業 EMS 標準
Protections : Short circuit / OLP / OVP
100% full load burn-in testNT$333NT$280 未稅加入購物車Quick View -
2路電機板+16路舵機擴展板 機器人機械臂小車底盤專用擴充板 適用於Arduino
0 滿分 5 分2路電機板+16路舵機擴展板Arudino UNO 機器人機械臂小車底盤
2 Motor && 16 Servo Drive Shield是兼容Arduino UNO和ESPduino的一款電機和舵機驅動模塊。模塊採用疊插式線路板設計,可以直接接入Arduino UNO 或者ESPduino線路板。該產品可以同時控制2 路直流電機(4.5 ~36V )和16 路舵機(5 ~18V ),適合於裝有機械臂的移動機器人驅動控制。
NT$619NT$500 未稅加入購物車Quick View -
MG90S 全金屬齒舵機 14g Servo 伺服機 品質穩定
0 滿分 5 分MG90S 全金屬齒舵機 14g Servo 伺服機
- 金屬銅齒、空心杯電機、雙滾珠軸承
- 產品型號:MG90s
- 產品重量:13.6g
- 產品尺寸:22.8*12.2*28.5mm
- 產品扭力:2.0kg(4.8v)
- 產品速度:0.11s(4.8v)
- 轉動角度:最大90°
- 舵機類型:數字舵機
- 使用溫度:0°-55°
- 死區設定:5微秒
- 插頭類型:JR、FUTABA通用
- 產品結構材質:金屬銅齒、空心杯電機、雙滾珠軸承
- 附件包含:舵盤、線長30CM、固定螺釘、減振膠套及鋁套等附件(詳見實拍圖)
- 適用範圍:450電直 斜盤舵機 固定翼 航模遙控飛機
NT$114NT$86 未稅加入購物車Quick View -
SG90 舵機 9克伺服機 伺服馬達 1.5Kg扭力 品質穩定
0 滿分 5 分180度
NT$95NT$57 未稅加入購物車Quick View -
四驅 4WD 四輪智慧小車底盤 / 自走車/ 機器人 底盤開發套件組
0 滿分 5 分NT$724NT$460 未稅加入購物車Quick View -
加入購物車Quick View
Grove – Voltage Divider 電阻分壓器 seeed原廠
0 滿分 5 分加入購物車Quick View -
Allegro A3967 轉譯型 步進馬達驅動板 EasyDriver Stepper Motor Driver V44
0 滿分 5 分Allegro A3967 轉譯型 步進馬達驅動板 EasyDriver Stepper Motor Driver V44
A3967 是美國allegro公司生產的pwm恆流控制微步距驅動二相步進電機專用驅動器。它的工作電壓可達30v,驅動電流達750ma,一個a3967slb即可驅動一台二相步進電機,可實現8細分驅動。芯片內部的pwm電流控制電路可通過加在pfd的電壓設置為慢、快、混合三種電流衰減模式,如果pfd端的電壓高於0.6vdd,則選擇慢衰減方式。若低於0.21vdd,則選擇快衰減模式。處於兩者之間為混合衰減模式。另外,a3967slb還能提供完善的保護措施,包括抑制瞬態電壓,過熱保護、防止電流直通、欠電壓自鎖等功能。a3967slb和微處理器之間不需要附加其他的接口電路,該芯片採easystepper 接口,將8條控制線減少了2條(步長和方向),只要簡單地輸入控制步進電機的脈衝,其內嵌的轉換器就可以實現對步進電機的控制。NT$171NT$143 未稅加入購物車Quick View -
MG996R 55G 90度-180度 金屬齒輪伺服器 舵機
0 滿分 5 分MG996R 90-180度 金屬齒輪伺服器 舵機 ,數位式 11 KG大扭力舵機/伺服馬達
脈寬信號 500-1500-2500,對應的角度是-90度~+90度
最新大扭力舵機MG996R (MG995升級產品)6v/11Kg ,原MG995的升級產品,是目前市場上較具性價比大扭力舵機之一
NT$305NT$257 未稅加入購物車Quick View -
加入購物車Quick View
微型振動馬達鈕扣型 扁平微型震動小馬達
0 滿分 5 分加入購物車Quick View -
加入購物車Quick View
DC 3V-6V 塑膠 直流減速馬達 減速比1:48
0 滿分 5 分單軸、雙軸 兩種規格可供選擇
加入購物車Quick View