匯承HC-08 低功耗 BLE CC2540 藍芽模組 4.0 主機/從機一體化 藍牙轉串口
NT$219 – NT$238 未稅
帶底板針腳(附排針需自行焊接)
HC-08 藍芽串口通信模組是新一代的基於Bluetooth Specification V4.0 BLE 藍芽協議的通訊模組。無線工作頻段為2.4GHz ISM,調製方式是GFSK。模組最大發射功率為4dBm,接收靈敏度-93dBm,空曠環境下和iphone4s 可以實現80 米超遠距離通信。模組採用郵票孔封裝方式,可貼片焊接,模組大小26.9mm×13mm×2.2mm,很方便客戶嵌入應用系統之內。
模組採用TI 的CC2540 晶片,配置256K Byte 空間,支援AT 指令,用戶可根據需要更改角色(主、從模式)以及UART串列傳輸速率、設備名稱等參數,使用靈活。
- 商品說明
商品說明
匯承HC-08 低功耗 BLE CC2540 藍芽模組 4.0 主機/從機一體化 藍牙轉串口
HC-08 藍芽串口通信模組是新一代的基於Bluetooth Specification V4.0 BLE 藍芽協議的通訊模組。無線工作頻段為2.4GHz ISM,調製方式是GFSK。模組最大發射功率為4dBm,接收靈敏度-93dBm,空曠環境下和iphone4s 可以實現80 米超遠距離通信。模組採用郵票孔封裝方式,可貼片焊接,模組大小26.9mm×13mm×2.2mm,很方便客戶嵌入應用系統之內。
模組採用TI 的CC2540 晶片,配置256K Byte 空間,支援AT 指令,用戶可根據需要更改角色(主、從模式)以及UART串列傳輸速率、設備名稱等參數,使用靈活。
請注意 使用手機或平板等裝置,要先確認是否有支援藍芽 BLE 4.0
HC-08藍牙模塊4.0 遠距離低功耗ble芯片主從一體無線串口模塊
藍牙4.0 BLE模塊,支持與iPhone4s和安卓4.3以上版本的手機連接,低功耗,傳輸距離為80米。底部帶有排針焊接口,免底板使用,快捷方便!
Wireless Bluetooth TTL Transceiver Module HC-08 CC2540 BLE CSR4.0
HC-08 firmware versions
- The default baud rate is 9600.
- There must be a delay between data packets. For example, if the baud rate is 1200 baud, the packet length is 120 bytes and the transmission time delay between packets must be not less than 2000ms otherwise you may lose data. The packet transmission time delay for 38400 baud with a packet length is 120 bytes must not be less than 200ms. At 115,200 baud with a packet length of 120 bytes, the transmission time delay between data packets must be not less than 50ms).
- When the baud rate is 19200 baud or more, the number o per packet cannot be more than 120 bytes.
- The higher the baud rate, the shorter the transmission delay time required between data packets.
- The shorter the number o per packet, the shorter the required delay time (e.g. 115,200 baud with a packet length of 20 bytes, the transmission delay time between data packets is less than 20ms).
HC-08 Pin Definition
TXD:串口發送,3.3V TTL電平。
RXD:串口接收,3.3V TTL電平。
CTS:串口流控,暫不支持。
RTS:串口流控,暫不支持。
DC:模擬、燒錄時鐘腳。
DD:模擬、燒錄數據腳。
RST:模組重定腳,要求不小於5ms的低電平進行復位。
VCC:模組電源腳,要求直流3.3V電源,供電電流不小於100mA。工作電壓範圍:2.0V~3.6V。
GND:模組公共地。
LED:模組指示燈輸出腳,高電平輸出,接LED時請串接電阻。
連線前,
主機未記錄從機位址時,每秒亮100ms;
主機記錄從機位址時,每秒亮900ms;
從機每2秒亮1秒。
連線後,LED常亮。
KEY:輸入腳,內部下拉。此腳接高電平,用於主機清除已記錄的從機位址。
- Pin 1: (UART TX) serial transmit, 3.3V TTL level.
- Pin 2: (UART RX) serial receive, 3.3V TTL level.
- Pin 3: (CTS) serial flow control, not supported.
- Pin 4: (RTS) serial flow control, not supported.
- Pin 11: (RST) reset pin; take LOW for not less than 5ms.
- Pin 12: (VCC) 2-3.6VDC operating voltage (typical 3.3VDC), current not less than 100mA.
- Pin 13: (VSS) common ground.
- Pin 22: (VSS) common ground.
- Pin 24: (LED) LED output pin; ON when paired/connected, PULSING when not paired/connected.
- Pin 26: (KEY): internal pulldown resistor keeps LOW for normal operation; HIGH erase pairing/connection information; after erasure, searches for new device to pair with/connect to randomly.
HC-08 AT commands
- AT responds OK
- AT + BAUDx responds with OKn where x is 1 – n is 1200, 2 – 2400, 3 – 4800, 4 – 9600 (default), 5 – 19200, 6 – 38400, 7 – 57600, 8 – 115200. Note: module must be reset after power-on for the new serial port baud rate to take effect.
- AT + NAMEname responds OKsetname – name is the Bluetooth device name to be set and must be 13 characters or fewer. Retained across power offs. Note: module must be reset after power-on for the new device name to take effect.
相關商品
-
加入購物車Quick View
X-NUCLEO-IDB05A1 EXPANSION BOARD, 藍芽擴充板 BLUETOOTH LOW ENERGY
0 滿分 5 分The X-NUCLEO-IDB05A1 is a Bluetooth low energy expansion board based on the SPBTLE-RF module for STM32 Nucleo. The X-NUCLEO-IDB05A1 is a Bluetooth Low Energy evaluation board based on the SPBTLE-RF BlueNRG-MS RF module to allow expansion of the STM32 Nucleo boards. The SPBTLE-RF module is FCC (FCC ID: S9NSPBTLERF) and IC certified (IC: 8976C-SPBTLERF). The X-NUCLEO-IDB05A1 is compatible with the ST Morpho and Arduino UNO R3 connector layout. The X-NUCLEO-IDB05A1 interfaces with the STM32 microcontroller via the SPI pin and the user can change the default SPI clock, the SPI chip select and SPI IRQ by changing one resistor on the evaluation board.
加入購物車Quick View -
420-450MHz Ultra low power data radio module 低功率無線數據傳輸模組
0 滿分 5 分WT-800T是一款高性能,低功耗,遠距離無線數據的微功耗射頻收發模塊,內置自動傳播的計算和序言CRC錯誤校正處理,在不改變用戶的任何數據和協議,採用半雙工透明傳輸機制來實現無線通信功能。模組的射頻芯片是基於擴頻跳頻技術,穩定性,抗干擾能力強和接收靈敏度超出了現有的GFSK模塊。配置的低功耗高速ST處理器,數據處理能力,運算速度都有所提高。
加入購物車Quick View -
加入購物車Quick View
美國官方授權經銷 ARDUINO NANO 33 BLE 義大利製 已焊針腳
0 滿分 5 分加入購物車Quick View -
加入購物車Quick View
JDY-08 帶底板藍牙 4.0 BLE 低功耗 CC2541 模組 支持 Airsync iBeacon
0 滿分 5 分JDY-08 帶底板藍牙 4.0 BLE 低功耗 CC2541 模組 支持 Airsync iBeacon
JDY-08 透傳模組是基於藍牙4.0協議標準,工作頻段為2.4GHZ範圍,調製方式為GFSK,最大發射功率為0db,最大發射距離80米,採用TICC2541晶片設計,支援用戶通過AT命令修改設備名、服務UUID、發射功率、配對密碼等指令,方便快捷使用靈活。
加入購物車Quick View -
RedBear DUO – Wi-Fi + BLE IoT Board 物聯網開發板 seeed原廠
0 滿分 5 分RedBear DUO – Wi-Fi + BLE IoT Board 物聯網開發板
RedBear公司所推出、尺寸只有姆指一般大的Duo開發板,能夠簡化物聯網裝置的開發流程,Duo提供了多種開發者需要的功能,支援Wi-Fi無線網 路、BLE低功耗藍牙等傳輸規範,還能夠支援RBLink擴充子板,讓開發者可以輕鬆擴充各種感應器以及功能模組,嘗試動手打造各種試作品或是成品。
RedBear先前曾推出第一款Arduino用的低功耗藍牙擴充板,過去也推出多款改版產品,在累積了一定IoT領域的經驗之後,RedBear這次推出了自有品牌的Duo開發板。
NT$886NT$790 未稅加入購物車Quick View -
加入購物車Quick View
HM-10 藍芽 4.0 模組 透明串口 藍牙串口 帶邏輯電平轉換/防反
0 滿分 5 分HM-10 藍芽 4.0 模組支援 iBeacon
當蘋果在今年夏天的「全球開發者大會」(WWDC)上首次提及「iBeacon」這一單詞的時候,他們例舉了上文中利用iBeacon快速購買演出門票的例子。但事實上,有關這一技術的實用領域還遠遠不限於此,因為這一技術的出現使得在室內環境下對使用者進行精確定位變成了可能。透過周邊多個iBeacon收發器,使用者的位置可以被精確定位至幾英尺的範圍內,這一定位技術被業內統稱為「微定位」(microlocation)。
加入購物車Quick View -
加入購物車Quick View
Bluetooth Mate Silver 藍芽模組 SparkFun原廠
0 滿分 5 分加入購物車Quick View -
加入購物車Quick View
JDY-18 藍牙 4.2 模組
0 滿分 5 分JDY-18 透傳模組是基於藍牙4.2協議標準,工作頻段為2.4GHZ範圍,調製方式為GFSK,最大發射功率為0db,最大發射距離60米,採用進口原裝芯片設計,支持用戶通過AT命令修改設備名、服務UUID、發射功率、配對密碼等指令,方便快捷使用靈活。JDY-18藍牙模組可以實現模塊與手機或模塊與模塊數據傳輸,可通過IO選擇UART或IIC通信方式,通過簡單的配置即可快速使用BLE藍牙進行產品應用。
加入購物車Quick View -
433 868 915MHz Ultra low power data radio module 低功耗無線數據傳輸模組 內附天線
0 滿分 5 分低功耗無線數據傳輸模組內附天線
加入購物車Quick View -
美國官方授權經銷 ARDUINO NANO 33 IOT 已焊排針 ESP32無線 / u-blox 藍芽 義大利製
0 滿分 5 分NT$1,143NT$1,040 未稅加入購物車Quick View