LoRa/GPS Shield For Arduino LoRa Bee 含 GPS 衛星定位模組 868MHz 無線射頻擴展板
NT$1,381 NT$1,240 未稅
LoRa部分,LoRa / GPS Shield採用SX1276 / SX1278收發器.LRRa / GPS Shield的收發器採用了LoRa™長距離調製解調器,可提供超長距離擴頻通信和高抗干擾能力,同時最小化電流消費。與常規調製技術相比,LoRa™在阻塞和選擇性方面也具有顯著的優勢,解決了傳感器在範圍,抗干擾能力和能量消耗之間的折衷。在GPS部分,L80 GPS(基於MTK MT3339)的添加是專為通過串行端口連接到GPS的應用程序而設計的,如定時應用或需要GPS信息的一般應用。該GPS模塊可以計算和使用存儲在內部閃存中的星曆數據(長達3天)自動預測軌道,因此即使在低功耗的室內信號水平下,屏蔽也可以快速固定位置。通過AlwaysLocate™技術,LoRa / GPS Shield可以自適應地調整開/關時間,根據環境和運動條件實現定位精度和功耗之間的平衡。GPS還支持自動天線切換功能。它可以實現內部貼片天線與外部主動天線的切換。
尚有庫存
- 商品說明
商品說明
LoRa/GPS Shield 868MHz For Arduino LoRa 含 GPS 衛星定位模組 無線射頻擴展板
LoRa / GPS Shield是用於與Arduino一起使用的LoRa™/ GPS 的擴展板。該產品適用於有興趣開發LoRa™/ GPS解決方案的用戶。LoRa / GPS Shield由LoRa / GPS Shield主板和LoRa BEE。
LoRa部分,LoRa / GPS Shield採用SX1276 / SX1278收發器.LRRa / GPS Shield的收發器採用了LoRa™長距離調製解調器,可提供超長距離擴頻通信和高抗干擾能力,同時最小化電流消費。與常規調製技術相比,LoRa™在阻塞和選擇性方面也具有顯著的優勢,解決了傳感器在範圍,抗干擾能力和能量消耗之間的折衷。在GPS部分,L80 GPS(基於MTK MT3339)的添加是專為通過串行端口連接到GPS的應用程序而設計的,如定時應用或需要GPS信息的一般應用。該GPS模塊可以計算和使用存儲在內部閃存中的星曆數據(長達3天)自動預測軌道,因此即使在低功耗的室內信號水平下,屏蔽也可以快速固定位置。通過AlwaysLocate™技術,LoRa / GPS Shield可以自適應地調整開/關時間,根據環境和運動條件實現定位精度和功耗之間的平衡。GPS還支持自動天線切換功能。它可以實現內部貼片天線與外部主動天線的切換。
- 頻段:868MHz
- 低功耗
- LoRa™調製解調器
- FSK,GFSK,MSK,GMSK,LoRa™和OOK調製
- 前導檢測
- 波特率可配置
- 內置溫度傳感器和低電量指示器
- 優異的阻斷免疫力
- 自動射頻感應和超快速AFC的CAD
- 支持DGPS,SBAS(WAAS / EGNOS / MSAS / GAGAN)
- 內部貼片天線與外部有源天線之間的GPS自動切換
- PPS VS. NMEA可以在時間服務中使用
- 支持SDK命令
- 內置LNA,靈敏度更高
- EASY™,無需外部存儲器的高級AGPS技術
- AlwaysLocate™,週期模式的智能控制器
- GPS FLP模式,正常模式功耗約為50%
- GPS支持短路保護和天線檢測
LoRa規格
- 168 dB最大鍊接預算。
- +20 dBm – 100 mW恆定RF輸出vs.
- +14 dBm高效PA。
- 可編程比特率高達300 kbps。
- 高靈敏度:低至-148 dBm。
- 防彈前端:IIP3 = -12.5 dBm。
- 優異的阻斷免疫力。
- 低的RX電流為10.3 mA,200 nA寄存器保持。
- 全集成合成器,分辨率為61 Hz。
- FSK,GFSK,MSK,GMSK,LoRaTM和OOK調製。
- 內置位同步器,用於時鐘恢復。
- 前導檢測。
- 127 dB動態範圍RSSI。
- 自動射頻感應和超快速AFC的CAD。
- 分組引擎最多256字節與CRC。
GPS規格
- 基於MT3339。
- 功率採集:25mA,功率跟踪:20mA。
- 符合GPS,SBAS。
- 可編程比特率高達300 kbps。
- 串行接口UART:可調4800〜115200 bps,默認值:9600bps。
- 更新率:1Hz(默認),最高10Hz。
- I / O電壓:2.7V〜2.9V。
- 協議:NMEA 0183,PMTK。
- 水平位置精度:自主<2.5米CEP。
- 使用EASY™的TTFF @ -130dBm:冷啟動<15s,熱啟動<5s,熱啟動<1s; TTFF@-130dBm。無EASY™:冷啟動<35s,熱啟動<30s,熱啟動<1s。
- 定時精度:1PPS輸出10ns,重新採集時間<1s。
- 速度精度無輔助<0.1m / s,加速精度無輔助0.1m /s²。
- 靈敏度採集-148dBm,跟踪-165dBm,重新採集-160dBm。
- 環境:工作溫度-40°C至85°C,存儲溫度-45°C至125°C。
- 動態性能高度Max.18000m,最大速度Max.515m / s,最大加速4G。
- L1波段接收器(1575.42MHz)通道22(跟踪)/ 66(採集)。
LoRa/GPS Shield For Arduino
The LoRa/GPS Shield is an expension board for LoRa™/GPS for using with the Arduino.This product is intended for those interested in developing LoRa™/GPS solutions.The LoRa/GPS Shield is composed of LoRa/GPS Shield mother board and LoRa BEE.
The LoRa/GPS Shield is an expension board for LoRa™/GPS for using with the Arduino.This product is intended for those interested in developing LoRa™/GPS solutions.The LoRa/GPS Shield is composed of LoRa/GPS Shield mother board and LoRa BEE.
In the LoRa part,the LoRa/GPS Shield is based on the SX1276/SX1278 transceiver.The transceivers of the LoRa/GPS Shield feature the LoRa™ long range modem that provides ultra-long range spread spectrum communication and high interference immunity whilst minimising current consumption. LoRa™ also provides significant advantages in both blocking and selectivity over conventional modulation techniques, solving the traditional design compromise between range,interference immunity and energy consumption.
In th GPS part,the add on L80 GPS (base on MTK MT3339) is designed for applications that use a GPS connected via the serial ports to the arduino such as timing applications or general applications that require GPS information.This GPS module can calculate and predict orbits automatically using the ephemeris data (up to 3 days) stored in internal flash memory, so the shield can fix position quickly even at indoor signal levels with low power consumption.With AlwaysLocate™ technology, the LoRa/GPS Shield can adaptively adjust the on/off time to achieve balance between positioning accuracy and power consumption according to the environmental and motion conditions.The GPS also supports automatic antenna switching function. It can achieve the switching between internal patch antenna and external active antenna.Moreover, it keeps positioning during the switching process.
- Frequency Band: 868 MHZ
- Low power consumption
- Compatible with Raspberry Pi 2 Model B/Raspberry Pi 3.
- LoRa™ Modem
- FSK, GFSK, MSK, GMSK, LoRa™ and OOK modulation
- Preamble detection
- Baud rate configurable
- Built-in temperature sensor and low battery indicator
- Excellent blocking immunity
- Automatic RF Sense and CAD with ultra-fast AFC
- Support DGPS, SBAS(WAAS/EGNOS/MSAS/GAGAN)
- GPS automatic switching between internal patch antenna and external active antenna
- PPS VS. NMEA can be used in time service
- Support SDK command
- Built-in LNA for better sensitivity
- EASY™, advanced AGPS technology without external memory
- AlwaysLocate™, an intelligent controller of periodic mode
- GPS FLP mode, about 50% power consumption of normal mode
- GPS support short circuit protection and antenna detection
LoRa Spec
- 168 dB maximum link budget.
- +20 dBm – 100 mW constant RF output vs.
- +14 dBm high efficiency PA.
- Programmable bit rate up to 300 kbps.
- High sensitivity: down to -148 dBm.
- Bullet-proof front end: IIP3 = -12.5 dBm.
- Excellent blocking immunity.
- Low RX current of 10.3 mA, 200 nA register retention.
- Fully integrated synthesizer with a resolution of 61 Hz.
- FSK, GFSK, MSK, GMSK, LoRaTM and OOK modulation.
- Built-in bit synchronizer for clock recovery.
- Preamble detection.
- 127 dB Dynamic Range RSSI.
- Automatic RF Sense and CAD with ultra-fast AFC.
- Packet engine up to 256 bytes with CRC.
GPS Spec
- Based on MT3339.
- Power Acquisition:25mA,Power Tracking:20mA.
- Compliant with GPS, SBAS.
- Programmable bit rate up to 300 kbps.
- Serial Interfaces UART: Adjustable 4800~115200 bps,Default: 9600bps.
- Update rate:1Hz (Default), up to10Hz.
- I/O Voltage:2.7V ~ 2.9V.
- Protocols:NMEA 0183,PMTK.
- Horizontal Position Accuracy:Autonomous <2.5 m CEP.
- TTFF@-130dBm with EASY™:Cold Start <15s,Warm Start <5s,Hot start <1s;TTFF@-130dBm.without EASY™:Cold Start <35s,Warm Start <30s,Hot Start <1s.
- Timing Accuracy:1PPS out 10ns,Reacquisition Time <1s.
- Velocity Accuracy Without aid <0.1m/s,Acceleration Accuracy Without aid 0.1m/s².
- Sensitivity Acquisition -148dBm,Tracking -165dBm,Reacquisition -160dBm.
- Environmental:Operating Temperature -40°C to 85°C,Storage Temperature -45°C to 125°C.
- Dynamic Performance Altitude Max.18000m,Maximum Velocity Max.515m/s,Maximum Acceleration 4G.
- L1 Band Receiver(1575.42MHz) Channel 22 (Tracking) /66 (Acquisition).
教學文件:https://wiki.dragino.com/index.php?title=Lora/GPS_Shield
相關商品
-
Relay Shield v3.0 繼電器擴充板支援Arduino單機片 seeed原廠
0 滿分 5 分如果你發現Arduino的小電流限制了你的發揮,那麼Relay Shield將會幫到你。這款Relay Shield簡單易用,它允許你使用簡單的靜態繼電器來控制4路大功率設備(每路上至8Amps,35 Volts)。
每一路都配備有LED指示燈以指示繼電器的當前工作狀態。高性能端子的使用使得Relay Shield的使用更加安全和可靠。對於大功率的Arduino項目或者機器人應用,這款Realy Shield將是理想的選擇。
NT$762NT$620 未稅加入購物車Quick View -
1Sheeld+ 高階版 Arduino 智慧手機多功能 擴展板 支援 iOS / Android 支援四十餘種功能
0 滿分 5 分高階版 Arduino 智慧手機多功能擴展板 支援 iOS / Android 支援四十餘種功能
1Sheeld +是一個易於配置的 Arduino 擴展板。它具有內置的藍牙模塊,可以讓您的Arduino能夠將自己連接到智慧手機。提供免費的 APP 可供串接應用。 Play Store和Apple Store上提供的1Sheeld +應用程序,您可以輕鬆地將 Android 和 iOS 智慧手機整合到你的專案
NT$2,724NT$2,238 未稅加入購物車Quick View -
加入購物車Quick View
美國官方授權經銷 Arduino ETHERNET SHIELD 2 乙太網路擴展板 2代 不含POE模組 義大利製
0 滿分 5 分義大利原廠 Arduino 乙太網路擴展板 2代 不含POE模組
Arduino Ethernet Shield 2 connects your Arduino board to the internet.
Plug The Arduino Ethernet Shield 2 module onto your Arduino Board, connect it to your network with an RJ45 cable (not included) and follow a few simple steps to start controlling your world through the internet. The Shield has a Power over Ethernet (PoE) module designed to extract power from a conventional Ethernet cable.
加入購物車Quick View -
CAN-BUS Shield v2.0 CANbus 控制器區域網路擴展板 適用於 Uno Leonardo MEGA2560 seeed原廠
0 滿分 5 分NT$800NT$667 未稅加入購物車Quick View -
Arduino GSM Shield 2 義大利製 Arduino 原廠進口 內建集成天線
0 滿分 5 分注意:GSM Shield 僅適用於 2G 網絡。購買前請檢查您所在的國家/地區是否有通行的2G電信網絡可使用,不接受電信網路問題退貨 !
Arduino GSM Shield 2 擴展板可以利用GPRS無線網絡將Arduino連至網際網路。只需將該擴充版插到Arduino板上,插入來自於提供GPRS業務的運營商的SIM卡,按照幾個簡單的步驟即可開始通過網際網路控制您的世界。您還可以撥打/接聽語音電話(您需要1個外部揚聲器和麥克風電路)和發送/接收SMS信息。
NT$3,900NT$3,560 未稅加入購物車Quick View -
SIM7000C NB-IoT / LTE / GPRS 相容Arduino 擴展板 DFRobot原廠
0 滿分 5 分SIM7000C NB-IoT/LTE/GPRS 擴展板同時支援普通SIM卡和NB-IoT專用卡,可以插接普通SIM卡進行打電話、發短信等傳統GSM應用
NT$2,190NT$1,760 未稅加入購物車Quick View -
L293D 馬達驅動擴展板/Motor Control Shield for Arduino
0 滿分 5 分L293D 馬達驅動擴展板 /Motor Control Shield for Arduino
Arduino 是一款很好的電子製作入門,有了馬達擴展板可以很好的成為機器人開發平臺。這裏介紹一款能驅動各種簡單到稍複雜項目的全功能的馬達擴展板。這是一款常用的直流馬達驅動模組,採用L293D晶片小電流直流馬達驅動晶片。管腳被做成了Arduino相容的,也方便了愛好者快速的基於Arduino的開發。
NT$229NT$114 未稅加入購物車Quick View -
PWM Shield 脈寬調變擴展板 SparkFun原廠
0 滿分 5 分SparkFun PWM 脈寬調變擴展板將允許您通過利用TLC5940 IC的電源從Arduino生成多達16個PWM信號。
NT$695NT$660 未稅加入購物車Quick View -
Data Logging shield 資料記錄器模組 支援Arduino 資料記錄擴展板
0 滿分 5 分注意:RTC電池座不附CR1220 3V鈕釦電池,若有需要請自行購買安裝。
NT$238NT$190 未稅加入購物車Quick View -
LCD Keypad Shield LCD 1602 液晶按鍵擴展板 相容Arduino
0 滿分 5 分NT$238NT$143 未稅加入購物車Quick View