匯承HC-08 低功耗 BLE CC2540 藍芽模組 4.0 主機/從機一體化 藍牙轉串口
NT$219 – NT$238 未稅
帶底板針腳(附排針需自行焊接)
HC-08 藍芽串口通信模組是新一代的基於Bluetooth Specification V4.0 BLE 藍芽協議的通訊模組。無線工作頻段為2.4GHz ISM,調製方式是GFSK。模組最大發射功率為4dBm,接收靈敏度-93dBm,空曠環境下和iphone4s 可以實現80 米超遠距離通信。模組採用郵票孔封裝方式,可貼片焊接,模組大小26.9mm×13mm×2.2mm,很方便客戶嵌入應用系統之內。
模組採用TI 的CC2540 晶片,配置256K Byte 空間,支援AT 指令,用戶可根據需要更改角色(主、從模式)以及UART串列傳輸速率、設備名稱等參數,使用靈活。
- 商品說明
商品說明
匯承HC-08 低功耗 BLE CC2540 藍芽模組 4.0 主機/從機一體化 藍牙轉串口
HC-08 藍芽串口通信模組是新一代的基於Bluetooth Specification V4.0 BLE 藍芽協議的通訊模組。無線工作頻段為2.4GHz ISM,調製方式是GFSK。模組最大發射功率為4dBm,接收靈敏度-93dBm,空曠環境下和iphone4s 可以實現80 米超遠距離通信。模組採用郵票孔封裝方式,可貼片焊接,模組大小26.9mm×13mm×2.2mm,很方便客戶嵌入應用系統之內。
模組採用TI 的CC2540 晶片,配置256K Byte 空間,支援AT 指令,用戶可根據需要更改角色(主、從模式)以及UART串列傳輸速率、設備名稱等參數,使用靈活。
請注意 使用手機或平板等裝置,要先確認是否有支援藍芽 BLE 4.0
HC-08藍牙模塊4.0 遠距離低功耗ble芯片主從一體無線串口模塊
藍牙4.0 BLE模塊,支持與iPhone4s和安卓4.3以上版本的手機連接,低功耗,傳輸距離為80米。底部帶有排針焊接口,免底板使用,快捷方便!
Wireless Bluetooth TTL Transceiver Module HC-08 CC2540 BLE CSR4.0
HC-08 firmware versions
- The default baud rate is 9600.
- There must be a delay between data packets. For example, if the baud rate is 1200 baud, the packet length is 120 bytes and the transmission time delay between packets must be not less than 2000ms otherwise you may lose data. The packet transmission time delay for 38400 baud with a packet length is 120 bytes must not be less than 200ms. At 115,200 baud with a packet length of 120 bytes, the transmission time delay between data packets must be not less than 50ms).
- When the baud rate is 19200 baud or more, the number o per packet cannot be more than 120 bytes.
- The higher the baud rate, the shorter the transmission delay time required between data packets.
- The shorter the number o per packet, the shorter the required delay time (e.g. 115,200 baud with a packet length of 20 bytes, the transmission delay time between data packets is less than 20ms).
HC-08 Pin Definition
TXD:串口發送,3.3V TTL電平。
RXD:串口接收,3.3V TTL電平。
CTS:串口流控,暫不支持。
RTS:串口流控,暫不支持。
DC:模擬、燒錄時鐘腳。
DD:模擬、燒錄數據腳。
RST:模組重定腳,要求不小於5ms的低電平進行復位。
VCC:模組電源腳,要求直流3.3V電源,供電電流不小於100mA。工作電壓範圍:2.0V~3.6V。
GND:模組公共地。
LED:模組指示燈輸出腳,高電平輸出,接LED時請串接電阻。
連線前,
主機未記錄從機位址時,每秒亮100ms;
主機記錄從機位址時,每秒亮900ms;
從機每2秒亮1秒。
連線後,LED常亮。
KEY:輸入腳,內部下拉。此腳接高電平,用於主機清除已記錄的從機位址。
- Pin 1: (UART TX) serial transmit, 3.3V TTL level.
- Pin 2: (UART RX) serial receive, 3.3V TTL level.
- Pin 3: (CTS) serial flow control, not supported.
- Pin 4: (RTS) serial flow control, not supported.
- Pin 11: (RST) reset pin; take LOW for not less than 5ms.
- Pin 12: (VCC) 2-3.6VDC operating voltage (typical 3.3VDC), current not less than 100mA.
- Pin 13: (VSS) common ground.
- Pin 22: (VSS) common ground.
- Pin 24: (LED) LED output pin; ON when paired/connected, PULSING when not paired/connected.
- Pin 26: (KEY): internal pulldown resistor keeps LOW for normal operation; HIGH erase pairing/connection information; after erasure, searches for new device to pair with/connect to randomly.
HC-08 AT commands
- AT responds OK
- AT + BAUDx responds with OKn where x is 1 – n is 1200, 2 – 2400, 3 – 4800, 4 – 9600 (default), 5 – 19200, 6 – 38400, 7 – 57600, 8 – 115200. Note: module must be reset after power-on for the new serial port baud rate to take effect.
- AT + NAMEname responds OKsetname – name is the Bluetooth device name to be set and must be 13 characters or fewer. Retained across power offs. Note: module must be reset after power-on for the new device name to take effect.
相關商品
-
HC-06 藍芽轉 UART 從機藍芽模組 具底板,提供Arduino 範例
0 滿分 5 分請勿將電源接到信號腳上,會直接燒壞模組!
兼容版跟原裝版的功能操作方法都相同!
加入購物車Quick View -
加入購物車Quick View
X-NUCLEO-IDB05A1 EXPANSION BOARD, 藍芽擴充板 BLUETOOTH LOW ENERGY
0 滿分 5 分The X-NUCLEO-IDB05A1 is a Bluetooth low energy expansion board based on the SPBTLE-RF module for STM32 Nucleo. The X-NUCLEO-IDB05A1 is a Bluetooth Low Energy evaluation board based on the SPBTLE-RF BlueNRG-MS RF module to allow expansion of the STM32 Nucleo boards. The SPBTLE-RF module is FCC (FCC ID: S9NSPBTLERF) and IC certified (IC: 8976C-SPBTLERF). The X-NUCLEO-IDB05A1 is compatible with the ST Morpho and Arduino UNO R3 connector layout. The X-NUCLEO-IDB05A1 interfaces with the STM32 microcontroller via the SPI pin and the user can change the default SPI clock, the SPI chip select and SPI IRQ by changing one resistor on the evaluation board.
加入購物車Quick View -
WiPy 2.0 藍芽 / Wi-Fi 開發板 Pycom seeed原裝進口
0 滿分 5 分WiPy 2.0 藍芽 / Wi-Fi 開發板 Pycom 原裝進口 Pycom WiPy MicroPython WiFi/藍牙開發板
WiPy 2.0是MicroPython啟用WiFi和藍牙開發板,專門設計用於物聯網應用。其核心在於Espressif ESP32片上系統(SoC),具有雙核微控制器、WiFi、藍牙和512 KB RAM。所有這些集成在一個板中,測量尺寸僅為42 x 20 x 3.5 mm!
NT$1,000NT$920 未稅加入購物車Quick View -
RFID 模組套件 RC522 FID 射頻IC卡感應模塊 含S50復旦卡、鑰匙扣
0 滿分 5 分RFID 模組套件 RC522 RFID 射頻IC卡感應模塊含S50復旦卡、鑰匙扣
MF RC522 是應用於13.56MHz非接觸式通信中高集成度的讀寫卡芯片,是針對“三表”應用推出的一款低電壓、低成本、體積小的非接觸式讀寫卡芯片,是智能儀表和便攜式手持設備研發的較好選擇。MF RC522利用了先進的調製和解調概念,完全集成了在13.56MHz下所有類型的被動非接觸式通信方式和協議。支持14443A兼容應答器信號。數字部分處理ISO14443A幀和錯誤檢測。此外,還支持快速CRYPTO1加密算法,用語驗證MIFARE系列產品。MFRC522支持MIFARE系列更高速的非接觸式通信,雙向數據傳輸速率高達424kbit/s。作為13.56MHz高集成度讀寫卡系列芯片家族的新成員,MF RC522與MF RC500和MF RC530有不少相似之處,同時也具備許多特點和差異。它與主機間通信採用SPI模式,有利於減少連線,縮小PCB板體積,降低成本。
NT$171NT$100 未稅加入購物車Quick View -
Grove – NFC 近場通訊模組 seeed原廠
0 滿分 5 分Grove – NFC 近場通訊是指短距離的無線通訊技術,應用的場合包括門禁管理系統和移動支付系統。近場通訊模塊集成了PN532收發芯片,在13.56MHz下無需接觸即可通訊,支持讀寫工作在13.56MHz的標籤,或者兩個近場通訊模塊可以完成點對點通信。近場通訊模塊配有的通訊接口包括I2C和UART,UART為默認的通訊方式。另外,模塊的天線引出的設計,無論你使用哪種盒子,都能方便地引出天線,給其他的設計騰出空間。
NT$762NT$680 未稅加入購物車Quick View -
Grove – BLE (dual model HM13) 藍牙4.0 模組 CSR雙模藍牙晶片 seeed原廠
0 滿分 5 分Grove – BLE (雙模)使用了CSR 雙模藍牙晶片,該晶片採用了ARM 架構支持AT 指令。用戶可以使用AT 指令靈活的配置串口波特率、設備名字、配對密碼等。
NT$790NT$600 未稅加入購物車Quick View -
加入購物車Quick View
HC-05 串口藍牙模組 (帶底板) 主機/從機可設定 / 帶底板,附 Arduino 範例
0 滿分 5 分請勿將電源接到信號腳上,會直接燒壞模組!
藍牙透傳模組只有4個AT指令,分別是測試通訊,改名稱,改串列傳輸速率,改配對密碼,AT指令必須從TXD,RXD信號腳設置,不能通過藍牙通道設置。發送AT指令的設備可以是各種類型的MCU(比如51,avr,pic,msp430,arm等),也可以是電腦通過串口(PC串口接MAX232以後或者USB轉串口)發送。
加入購物車Quick View -
加入購物車Quick View
Bluetooth Mate Silver 藍芽模組 SparkFun原廠
0 滿分 5 分加入購物車Quick View -
加入購物車Quick View
HM-10 CC2541 主從一體 藍牙4.0模組 BT4.0 / BLE 帶邏輯電平轉換
0 滿分 5 分加入購物車Quick View -
加入購物車Quick View
美國官方授權經銷 ARDUINO NANO 33 BLE 義大利製 已焊針腳
0 滿分 5 分加入購物車Quick View