- 商品說明
商品說明
Gravity: Analog Signal Isolator 模擬信號隔離器
在許多情況下,需要電隔離以確保傳感器的可靠操作。有些傳感器,例如 pH傳感器 和電導率傳感器,當它們連接到相同的電源時,它們會相互干擾並且不能在同一容器中正確測量。為了確保傳感器穩定可靠地運行而沒有干擾,有必要隔離信號和電源。
重力:模擬信號隔離器可有效防止傳感器之間的電氣干擾。該模塊具有板載5V隔離電源,可直接為傳感器供電。因此,您不需要準備外接電源,這樣簡單實用!電線連接器專為DFRobot 3Pin模擬傳感器設計,即插即用,無需焊接。模擬信號傳輸比為1:1,當該模塊連接到電路時,這對傳感器的輸出信號的影響非常小。此外,您不需要更改主板的代碼。
該anlaog信號隔離器適用於防止傳感器之間的干擾,例如需要防止水傳感器之間干擾的多參數水質監測系統。
接口說明
Gravity: Analog Signal Isolator 接口
- MCU端子(非隔離端子)應提供5.0±0.1V的精確電壓。輸入電壓精度越高,模擬輸出信號的精度越高。
- 該模塊在工作期間消耗相對較大的電流,因此您最好為Arduino板提供外部電源,以保證足夠的功率和電壓精度。
- 請注意傳感器或模塊的工作電流,SEN端子的最大輸出電流為170mA。
- MCU端子(非隔離端子)的GND和SEN端子(隔離端子)的GND彼此隔離。不要將它們短路。
- 隔離器工作時產生熱量是正常的。
接線圖
規格
- 工作電壓:5.0V
- 響應時間:4秒(典型值)
- 兩個端子之間的模擬誤差:<±20mV(典型值)
- Conector類型:PH2.0-3P
- 空載電流:75mA
- 尺寸:42 * 32mm / 1.65 * 1.26英寸
- 非隔離端子(MCU端子)
電源電壓:5.0±0.1V
模擬輸出:0~5.0V - 隔離端子(SEN端子)
輸出電壓:5.0±0.2V
模擬輸入:0~5.0V
出貨清單
- 模擬信號隔離器 x1
- PH2.0-3P 連接線 x2
Documents
=========================================================
Gravity: Analog Signal Isolator
In many cases, electrical isolation is required to ensure reliable operation of the sensors. Some sensors, such as pH sensors and conductivity sensors,they will interfere with each other and do not measure properly in the same container when they connect to the same power .To ensure stable and reliable operation of the sensors with no interference,it is necessary to isolate the signal and the power.
Gravity: Analog Signal Isolator is efficient in preventing the electrical interference between sensors. This module has an onboard 5V isolation power which could directly supply to the sensor. Therefore, you do not need to prepare the external power, such an easy and practical! The connector of wires are special designed for DFRobot 3Pin analog sensor, plug and play, no need for soldering. The analog signal transmission ratio is 1:1, which contributes to a very small impact on output signals of sensors when this module connect into the circuit. Futher more, you do not need to change the code of the mainboard.
This anlaog signal isolator is applicable to prevent interferences between sensors, such as multi-parameter water quality monitoring system that need to prevent interferences between water sensors.
Gravity: Analog Signal Isolator Interface
This product is almost compatible with all analog sensors produced by DFRobot. It could satisfy varied demands in situations which require electrical isolation.
- The MCU terminal (non-isolation terminal) should be provided with precise voltage of 5.0±0.1V. The higher the precision of input voltage, the higher the precision of analog output signal.
- This module consumes relatively large current during operation, so you’d better to provide external power supply to Arduino board to guarantee enough power and voltage precision.
- Please pay attention to the operating current of your sensor or module, the maximum output current from SEN terminal is 170mA.
- The GND of the MCU terminal(non-isolation terminal) and the GND of SEN terminal (isolation terminal) are isolated from each other. Do not short circuit them.
- It is normal for the isolator generates heat while working.
SPECIFICATION
- Operating Voltage: 5.0V
- Response Time: 4 seconds (Typ)
- Analog Error between Two Terminals: <± 20mV (Typ)
- Conector Type: PH2.0-3P
- No-load Current: 75mA
- Dimension: 42 * 32mm / 1.65 * 1.26 inch
- Non-isolation Terminal (MCU Terminal)
Supply Voltage: 5.0 ± 0.1V
Analog Output: 0 ~ 5.0V - Isolation Terminal (SEN Terminal)
Output Voltage: 5.0 ± 0.2V
Analog Input: 0 ~ 5.0V
DOCUMENTS
SHIPPING LIST
- Gravity: Analog Signal Isolator x1
- PH2.0-3P Cable x2
相關商品
-
Grove – Recorder v3.0 錄音感測器 錄音機 語音錄放模組 seeed原廠
0 滿分 5 分NT$733NT$560 未稅加入購物車Quick View -
加入購物車Quick View
HC-05 串口藍牙模組 (帶底板) 主機/從機可設定 / 帶底板,附 Arduino 範例
0 滿分 5 分請勿將電源接到信號腳上,會直接燒壞模組!
藍牙透傳模組只有4個AT指令,分別是測試通訊,改名稱,改串列傳輸速率,改配對密碼,AT指令必須從TXD,RXD信號腳設置,不能通過藍牙通道設置。發送AT指令的設備可以是各種類型的MCU(比如51,avr,pic,msp430,arm等),也可以是電腦通過串口(PC串口接MAX232以後或者USB轉串口)發送。
加入購物車Quick View -
1000cm長度 10米 防水探針型熱電偶溫度感測器 不銹鋼封裝 防水型 DS18b20 溫度感測器
0 滿分 5 分本溫度感測器包括一個金屬探測器和 1000cm(10米) 的電纜,具有較寬的溫度測量範圍 (-55 ° C 到 125 ° C ),適合沉浸式溫度檢測。注意事項: 電纜線部分不能承受溫度高於 105 ° c
優質不銹鋼管封裝 防水防潮防生鏽,探頭採用原装DS18B20溫度傳感器晶片,每個引腳均用熱縮管隔開,防止短路,內部封膠,防水防潮,優質不銹鋼管封裝防生鏽
不銹鋼外殼(6*50mm),引線長度 1000cm
3.0V~5.5V供電
9~12位可調分辨率
感溫範圍寬-55℃ ~ +125℃
輸出引線:紅色(VCC),藍(黃)色(DATA),黑色(GND)
NT$524NT$280 未稅加入購物車Quick View -
Grove – Gas Sensor(MQ5) 氣體感測器 Seeed原廠
0 滿分 5 分可檢測液化石油氣,天然氣,城鎮煤氣等。基於其快速響應時間,測量可以盡快進行。且其靈敏度也可以通過電位器來進行調節。
NT$276NT$220 未稅加入購物車Quick View -
加入購物車Quick View
Gravity: I2C 非接觸式紅外線溫度感測器 MLX90614 for Arduino DFRobot原廠
0 滿分 5 分加入購物車Quick View -
Grove – Infrared Temperature Sensor 紅外線 溫度感測器模組 seeed原廠
0 滿分 5 分紅外溫度傳感器通過接收物體發出的紅外線來測量其溫度。
NT$457NT$380 未稅加入購物車Quick View -
Grove – Gas Sensor(MQ3) 酒精濃度 氣體 感測器模組 seeed原廠
0 滿分 5 分它可以檢測酒精,汽油,甲烷,己烷,液化石油氣,CO 其感測速度與回應的非常靈敏快速。也靈敏度可以由電位進行調整。
NT$362NT$240 未稅加入購物車Quick View -
Grove – Air quality sensor v1.3 空氣品質感測器模組 seeed原廠
0 滿分 5 分主要可以監測的氣體是一氧化碳,醇,丙酮,稀釋劑,甲醛等輕微毒性氣體。本模組兼容 5V和3.3V電源。
NT$457NT$300 未稅加入購物車Quick View -
2000cm長度 / 20米 防水探針型熱電偶溫度感測器 不銹鋼封裝 防水型 DS18b20溫度感測器
0 滿分 5 分本溫度感測器包括一個金屬探測器和 2000cm(20米) 的電纜,具有較寬的溫度測量範圍 (-55 ° C 到 125 ° C ),適合沉浸式溫度檢測。注意事項: 電纜線部分不能承受溫度高於 105 ° c
優質不銹鋼管封裝 防水防潮防生鏽,探頭採用原装DS18B20溫度傳感器晶片,每個引腳均用熱縮管隔開,防止短路,內部封膠,防水防潮,優質不銹鋼管封裝防生鏽
不銹鋼外殼(6*50mm),引線長度2000cm
3.0V~5.5V供電
9~12位可調分辨率
感溫範圍寬-55℃ ~ +125℃
輸出引線:紅色(VCC),藍(黃)色(DATA),黑色(GND)
NT$600NT$420 未稅加入購物車Quick View -
Grove – PIR Motion Sensor 紅外線人體移動探測感測器 seeed原廠
0 滿分 5 分這是一個極易使用的紅外線 PIR人體運動探測感測器。通過這個感測器,你可以使你的作品對運動,例如人類的運動作出互動。只要將其接到Grove – Base Shield上,並且下載程序,當有人走入它的探測範圍時,PIR運動探測傳感器就會在它的SIG腳上輸出一個HIGH信號。
NT$333NT$260 未稅加入購物車Quick View