- 商品說明
商品說明
Gravity: Analog Signal Isolator 模擬信號隔離器
在許多情況下,需要電隔離以確保傳感器的可靠操作。有些傳感器,例如 pH傳感器 和電導率傳感器,當它們連接到相同的電源時,它們會相互干擾並且不能在同一容器中正確測量。為了確保傳感器穩定可靠地運行而沒有干擾,有必要隔離信號和電源。
重力:模擬信號隔離器可有效防止傳感器之間的電氣干擾。該模塊具有板載5V隔離電源,可直接為傳感器供電。因此,您不需要準備外接電源,這樣簡單實用!電線連接器專為DFRobot 3Pin模擬傳感器設計,即插即用,無需焊接。模擬信號傳輸比為1:1,當該模塊連接到電路時,這對傳感器的輸出信號的影響非常小。此外,您不需要更改主板的代碼。
該anlaog信號隔離器適用於防止傳感器之間的干擾,例如需要防止水傳感器之間干擾的多參數水質監測系統。
接口說明
Gravity: Analog Signal Isolator 接口
- MCU端子(非隔離端子)應提供5.0±0.1V的精確電壓。輸入電壓精度越高,模擬輸出信號的精度越高。
- 該模塊在工作期間消耗相對較大的電流,因此您最好為Arduino板提供外部電源,以保證足夠的功率和電壓精度。
- 請注意傳感器或模塊的工作電流,SEN端子的最大輸出電流為170mA。
- MCU端子(非隔離端子)的GND和SEN端子(隔離端子)的GND彼此隔離。不要將它們短路。
- 隔離器工作時產生熱量是正常的。
接線圖
規格
- 工作電壓:5.0V
- 響應時間:4秒(典型值)
- 兩個端子之間的模擬誤差:<±20mV(典型值)
- Conector類型:PH2.0-3P
- 空載電流:75mA
- 尺寸:42 * 32mm / 1.65 * 1.26英寸
- 非隔離端子(MCU端子)
電源電壓:5.0±0.1V
模擬輸出:0~5.0V - 隔離端子(SEN端子)
輸出電壓:5.0±0.2V
模擬輸入:0~5.0V
出貨清單
- 模擬信號隔離器 x1
- PH2.0-3P 連接線 x2
Documents
=========================================================
Gravity: Analog Signal Isolator
In many cases, electrical isolation is required to ensure reliable operation of the sensors. Some sensors, such as pH sensors and conductivity sensors,they will interfere with each other and do not measure properly in the same container when they connect to the same power .To ensure stable and reliable operation of the sensors with no interference,it is necessary to isolate the signal and the power.
Gravity: Analog Signal Isolator is efficient in preventing the electrical interference between sensors. This module has an onboard 5V isolation power which could directly supply to the sensor. Therefore, you do not need to prepare the external power, such an easy and practical! The connector of wires are special designed for DFRobot 3Pin analog sensor, plug and play, no need for soldering. The analog signal transmission ratio is 1:1, which contributes to a very small impact on output signals of sensors when this module connect into the circuit. Futher more, you do not need to change the code of the mainboard.
This anlaog signal isolator is applicable to prevent interferences between sensors, such as multi-parameter water quality monitoring system that need to prevent interferences between water sensors.
Gravity: Analog Signal Isolator Interface
This product is almost compatible with all analog sensors produced by DFRobot. It could satisfy varied demands in situations which require electrical isolation.
- The MCU terminal (non-isolation terminal) should be provided with precise voltage of 5.0±0.1V. The higher the precision of input voltage, the higher the precision of analog output signal.
- This module consumes relatively large current during operation, so you’d better to provide external power supply to Arduino board to guarantee enough power and voltage precision.
- Please pay attention to the operating current of your sensor or module, the maximum output current from SEN terminal is 170mA.
- The GND of the MCU terminal(non-isolation terminal) and the GND of SEN terminal (isolation terminal) are isolated from each other. Do not short circuit them.
- It is normal for the isolator generates heat while working.
SPECIFICATION
- Operating Voltage: 5.0V
- Response Time: 4 seconds (Typ)
- Analog Error between Two Terminals: <± 20mV (Typ)
- Conector Type: PH2.0-3P
- No-load Current: 75mA
- Dimension: 42 * 32mm / 1.65 * 1.26 inch
- Non-isolation Terminal (MCU Terminal)
Supply Voltage: 5.0 ± 0.1V
Analog Output: 0 ~ 5.0V - Isolation Terminal (SEN Terminal)
Output Voltage: 5.0 ± 0.2V
Analog Input: 0 ~ 5.0V
DOCUMENTS
SHIPPING LIST
- Gravity: Analog Signal Isolator x1
- PH2.0-3P Cable x2
相關商品
-
加入購物車Quick View
TXB0104 電壓位準 I/O轉換板 4bit SparkFun原廠
0 滿分 5 分Texas Instruments TXB0104 模組的擴展板。TXB0104是一款具有自動方向感應功能的4位雙向電壓電平轉換器。這個4位非反相轉換器使用兩個獨立的可配置電源軌。A端口旨在跟踪VCCA。VCCA接受1.2V至3.6V的任何電源電壓。B端口用於跟踪VCCB。VCCB接受1.65V至5.5V的任何電源電壓。這允許在1.2V,1.5V,1.8V,2.5V,3.3V和5V電壓節點之間進行通用的低壓雙向轉換。VCCA不應超過VCCB。我們已經打破了這個模塊上的每個引腳,您可以輕鬆訪問A和B端口。
加入購物車Quick View -
Grove – Infrared Temperature Sensor 紅外線 溫度感測器模組 seeed原廠
0 滿分 5 分紅外溫度傳感器通過接收物體發出的紅外線來測量其溫度。
NT$457NT$380 未稅加入購物車Quick View -
加入購物車Quick View
2路電平轉換模組帶隔離 2-Channel Level Converter (12V to 5V) DFRobot原廠
0 滿分 5 分加入購物車Quick View -
Grove – GPS Module 衛星模組 適用於 Arduino 與 Raspberry Pi seeed原廠
0 滿分 5 分Grove – GPS模組是一款低成本及可程式設計的GPS模組,可用於手持設備GPS資料的採集。模組採用串口通信,可通過串口進行資料的讀取。它設有一個50通道的u-blox 5定位引擎,首次定位時間(TTFF)小於1s。跟蹤和採集的靈敏度均達到-160dBm,適用於個人導航及位置服務的專案。
NT$857NT$700 未稅加入購物車Quick View -
3000cm長度 30米 防水探針型熱電偶溫度感測器 不銹鋼封裝 防水型 DS18b20 溫度感測器
0 滿分 5 分本溫度感測器包括一個金屬探測器和 3000cm(30米) 的電纜,具有較寬的溫度測量範圍 (-55 ° C 到 125 ° C ),適合沉浸式溫度檢測。注意事項: 電纜線部分不能承受溫度高於 105 ° c
優質不銹鋼管封裝 防水防潮防生鏽,探頭採用原装DS18B20溫度傳感器晶片,每個引腳均用熱縮管隔開,防止短路,內部封膠,防水防潮,優質不銹鋼管封裝防生鏽
不銹鋼外殼(6*50mm),引線長度 3000cm
3.0V~5.5V供電
9~12位可調分辨率
感溫範圍寬-55℃ ~ +125℃
輸出引線:紅色(VCC),藍(黃)色(DATA),黑色(GND)
NT$667NT$620 未稅加入購物車Quick View -
加入購物車Quick View
Grove – Rotary Angle Sensor 旋轉角度電位器模組 seeed原廠
0 滿分 5 分加入購物車Quick View -
Grove – Gas Sensor(MQ3) 酒精濃度 氣體 感測器模組 seeed原廠
0 滿分 5 分它可以檢測酒精,汽油,甲烷,己烷,液化石油氣,CO 其感測速度與回應的非常靈敏快速。也靈敏度可以由電位進行調整。
NT$362NT$240 未稅加入購物車Quick View -
Fermion:LWLP5000 差壓感測器±500pa DFRobot原廠
0 滿分 5 分NT$1,524NT$1,420 未稅加入購物車Quick View -
Grove – Air quality sensor v1.3 空氣品質感測器模組 seeed原廠
0 滿分 5 分主要可以監測的氣體是一氧化碳,醇,丙酮,稀釋劑,甲醛等輕微毒性氣體。本模組兼容 5V和3.3V電源。
NT$457NT$300 未稅加入購物車Quick View -
Grove – RTC 高精度時間模組 seeed原廠
0 滿分 5 分支持I2C協議的時鐘芯片DS1307。它使用鋰電池(CR1225)。時鐘/日曆提供秒,分,小時,日,日,月和年信息。
NT$271NT$220 未稅加入購物車Quick View