FTDI Basic Breakout – 5V FT232RL晶片 SparkFun原廠
NT$695 NT$500 未稅
尚有庫存
- 商品說明
商品說明
FTDI Basic Breakout – 5V FT232RL晶片 美國 SparkFun 原裝進口
這是 Sparkfun FTDI Basic 的最新版本。我底部使用SMD 6針頭,這使得它更小更緊湊。功能一直保持不變。這是FTDI FT232RL USB串行IC的功能擴展板。該板的引腳排列與FTDI電纜匹配使用官方Arduino和副廠的5V Arduino板。它也可以用於一般串行應用。與該板的主要區別在於它引出DTR引腳,而不是FTDI電纜的RTS引腳。當下載新的草圖時,DTR引腳允許Arduino目標自動復位。這是一個非常好的功能,讓您可以下載草圖,而無需點擊重置按鈕。
標記為BLK和GRN的引腳對應於FTDI電纜上的有色導線。FTDI電纜上的黑線為GND,綠色為CTS。使用這些BLK和GRN引腳將FTDI基板與Arduino目標對齊。該電路板具有TX和RX LED,通過FTDI電纜可以更好地使用。您實際上可以看到LED上的串行流量,以驗證電路板是否正常工作。該板旨在降低Arduino開發成本,並提高易用性(自動重置功能!)。我們的Arduino Pro板和LilyPads使用這種類型的連接器。該板的一個很好的功能是板背面的跳線,允許將板配置為3.3V或5V(電源輸出和IO電平)。該闆卡默認為5V,但如果需要切換到3.3V,則可以切斷默認軌跡並添加焊接跳線。
Document
=========================================================
SparkFun FTDI Basic Breakout – 5V
This is the newest revision of our FTDI Basic. We now use a SMD 6-pin header on the bottom, which makes it smaller and more compact. Functionality has remained the same.
This is a basic breakout board for the FTDI FT232RL USB to serial IC. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 5V Arduino boards. It can also be used for general serial applications. The major difference with this board is that it brings out the DTR pin as opposed to the RTS pin of the FTDI cable. The DTR pin allows an Arduino target to auto-reset when a new Sketch is downloaded. This is a really nice feature to have and allows a sketch to be downloaded without having to hit the reset button. This board will auto reset any Arduino board that has the reset pin brought out to a 6-pin connector.
The pins labeled BLK and GRN correspond to the colored wires on the FTDI cable. The black wire on the FTDI cable is GND, green is CTS. Use these BLK and GRN pins to align the FTDI basic board with your Arduino target.
This board has TX and RX LEDs that make it a bit better to use over the FTDI cable. You can actually see serial traffic on the LEDs to verify if the board is working.
This board was designed to decrease the cost of Arduino development and increase ease of use (the auto-reset feature rocks!). Our Arduino Pro boards and LilyPads use this type of connector.
One of the nice features of this board is a jumper on the back of the board that allows the board to be configured to either 3.3V or 5V (both power output and IO level). This board ship default to 5V, but you can cut the default trace and add a solder jumper if you need to switch to 3.3V.
Documents:
- Schematic
- Eagle Files
- USB to serial UART Boards Hookup Guide
- How to Install FTDI Drivers
- FTDI Drivers
- GitHub (Design Files)
相關商品
-
副廠 Esplora 遊戲機開發控制板 GamePad 採用原廠晶片支援Arduino
0 滿分 5 分Esplora 是 Leonardo 的增強版,控制晶片依舊採用Leonardo用的Atmega32U4,可以直接控制USB與上位機的通信,模擬PC機的鍵盤和鼠標等外設。Esplora最突出的特性是增加了幾個內建的輸入設備和傳感器,還有幾個輸入輸出接口。
NT$848NT$790 未稅加入購物車Quick View -
Grove Shield 擴展板 for Arduino Nano、Seeeduino Nano seeed原廠
0 滿分 5 分Grove Shield for Arduino Nano 擴展板是為Arduino Nano製作的,也可以與Seeeduino Nano一起使用 。在Grove系統的幫助下,您可以通過簡單的插頭將數百個Grove傳感器,Grove執行器和Grove顯示器連接到Arduino Nano。
NT$190NT$140 未稅加入購物車Quick View -
ADS1115 四通道 超小型16位精密模數轉換器(ADC) 開發板模組
0 滿分 5 分NT$295NT$200 未稅加入購物車Quick View -
UNO ABS 工控專用機殼可壁掛
0 滿分 5 分UNO ABS 機殼 兼容市面上UNO R3 系列主板,包括官方義大利正廠,副廠的,統統兼容,免鎖螺絲!
可視性強各接口均有對應開口設置,非一般市面上常見的易碎壓克力殼
圖片為裝上UNO主板的示意圖,注意本商品不包含開發板,出貨只有單ABS工控機殼
NT$238NT$95 未稅加入購物車Quick View -
IIC / I2C 介面 LCD 1602 2004 轉接板
0 滿分 5 分IIC/I2C LCD 1602,2004 轉接板不含 LCD 螢幕
Arduino控制板IO口只有20個,加些傳感器、SD卡啥的,繼電器等模塊多了,IO口就不夠用了,原來的1602屏需要7個IO口才能驅動起來,我們開發的這個模塊可以幫你省5個IO口
產品參數:
- 尺寸:41.5mm(長)*19mm(寬)*15.3mm(高)
- 重量:5g
- PCB顏色:黑色
- 供電電壓:2.5-6V
- 支持I2C協議
- 帶背光電源控制,可以通過跳線帽設置是否連接背光電源。插上跳線帽為連接背光電源,拔掉跳線帽為斷開背光電源
- 對比度可調節,旋轉藍色電位器,順時針增強,逆時針減弱。電位器設計在正面,方便客戶隨時隨地自由調節
- 模塊可級聯,最多可級聯8個。通過短路A0/A1/A2修改設備地址。默認地址為0x27
NT$62NT$40 未稅加入購物車Quick View -
MCU-arduino CP2102 模組 USB 轉TTL USB轉串口 UART STC下載器
0 滿分 5 分NT$114NT$86 未稅加入購物車Quick View -
加入購物車Quick View
Gravity:Analog Electrical Conductivity Sensor / Meter 模擬電導率感測器 液體檢測 水質監測 相容Arduino、樹莓派
0 滿分 5 分Gravity:模擬電導率計專門用於測量水溶液的電導率值,評估水質狀況,產品配合主控板與配套的軟件庫,就可迅速搭建出一套電導率檢測儀,即插即用,無需焊接。
K值差異(1/10)簡單說就是可檢測液體濃度的差別,K=1檢測一般水,K=10檢測海水
加入購物車Quick View -
Gravity: Bluno Beetle Shield Beetle BLE 多功能擴展板 DFRobot原廠
0 滿分 5 分只要按照說明,將Bluno Beetle焊接在上面,你就可以直插3pin的傳感器和其他擴展設備。另外,擴展板還具備外接電源接口,可直接外接供電。
NT$333NT$260 未稅加入購物車Quick View -
加入購物車Quick View
Analog/Digital MUX Breakout-CD74HC4067 數位/類比轉換板 16通道 Sparkfun原廠
0 滿分 5 分加入購物車Quick View -
加入購物車Quick View
TCA9548A I2C Multiplexer 8路 IIC I2C 多路擴展板模組
0 滿分 5 分在你的Arduino項目中經常會遇到,需要Arduino與多個I2C零件連接起來。例如,由4個OLED組成一個大型顯示器,或者是7個溫度傳感器同時處理的雞蛋孵化室。這些類型的問題,可以通過 TCA9548A 1-to-8 I2C 多路接駁模組來解決。
加入購物車Quick View