Gravity: Digital I2C Signal Isolator 數字I2C 信號隔離器 DFRobot原廠
NT$619 NT$560 未稅
數字信號隔離器能夠隔離I2C數字信號並為傳感器模塊提供隔離電源,有效防止傳感器模塊之間的相互干擾。該數字信號隔離器可用於多參數水質檢測系統,以防止水質傳感器相互干擾。
尚有庫存
- 商品說明
商品說明
Gravity: Digital I2C Signal Isolator 數字I2C 信號隔離器
Digital I2C Signal Isolator 數字信號隔離器能夠隔離I2C數字信號並為傳感器模塊提供隔離電源,有效防止傳感器模塊之間的相互干擾。該數字信號隔離器可用於多參數水質檢測系統,以防止水質傳感器相互干擾。
在許多情況下,存在干擾源。例如,魚缸中的運行泵將向水中釋放信號,這會干擾魚缸中的傳感器。在這種情況下,需要電隔離以確保傳感器的穩定操作。一些傳感器,如pH傳感器和電導率傳感器,在同一容器中共用相同的電源和測量值,會相互干擾,無法正常工作。為了確保傳感器模塊的穩定運行,必須隔離信號和電源。
在模擬信號隔離器之後,我們推出了這種數字信號隔離器,專門隔離I2C數字信號。此外,板載5V隔離電源芯片可直接為傳感器模塊供電,無需額外電源。本產品專為 DFRobot I2C 連接器傳感器或模塊而設計,即插即用,無需焊接。將其連接到電路中進行電氣隔離,控制板上的傳感器模塊代碼無需修改,簡單方便。
接口說明
- 1.Module端(隔離端)最大輸出電流不得超過150mA,請注意負載的工作電流!
- 2.Module端(隔離端)的所有管腳與Controller端(非隔離端)的所有管腳之間是相互隔離的,嚴禁將其短接!
- 3.工作過程中,隔離電源模塊會發熱,屬正常現象。
注意:
接線圖
特徵
- 板載5V 0.75W隔離電源芯片,無需額外電源,簡單方便
- 幾乎兼容所有DFRobot I2C連接器傳感器或模塊,即插即用,無需焊接
規格
- 工作電壓:5.0V
- 連接器類型:PH2.0-4P
- 接口協議:I2C(IIC)
- 接口信號電平:高3.3V,低0V
- 尺寸:42 * 32mm / 1.65 * 1.26英寸
控制器側(非隔離側)
- 電源電壓:5.0±0.15V
- 空載電流:15mA(TYP)
模塊側(隔離側)
- 輸出電壓:5.0±0.15V
- 輸出電流:150mA(MAX)
出貨清單
- 重力:數字I2C 信號隔離器 x1
- 雙PH2.0-4P電纜x1
- 重力-4P I2C / UART 傳感器電纜 x1
- XH2.54-4Pin x2
Documents
=========================================================
Gravity: Digital I2C Signal Isolator
Gravity: Digital Signal Isolator is capable of isolating I2C digital signal and providing isolated power to the sensor module, effectively preventing mutual interference between the sensor modules. This digital signal isolator can be used for multi-parameter water quality detection systems to prevent water quality sensors from interfering with each other.
In many cases, interference sources are existing. For example, a running pump in a fish tank will release signals into the water, which interferes the sensors in the fish tank. In this case, electrical isolation is needed to ensure the stable operation of the sensors. Some sensors, such as pH sensors and electrical conductivity sensors, which share the same power source and measure in the same container, will interfere with each other and do not work properly. In order to ensure stable operation of the sensor modules, it is necessary to isolate the signal and the power.
After the analog signal isolator, we launched this digital signal isolator which specifically isolates the I2C digital signal. What’s more, the on-board 5V isolation power chip can directly supply the sensor module, without additional power. This product is designed specifically for DFRobot I2C connector sensor or modules, plug and play, no welding. Connect it into your circuit to get electrical isolation, and the code of sensor module in control board does not need to be modified, which is simple and convenient.
Note:
2. All pins on the Module side (isolation side) are isolated from all pins on the Controller side (non-isolation side). Do not short-circuit them.
3. It is normal for the isolator generates heat while working.
FEATURES
- Onboard 5V 0.75W isolation power chip, no additional power needed, simple and convenient
- Almost compatible with all DFRobot I2C connector sensors or modules, plug and play, no welding
SPECIFICATION
- Operating Voltage: 5.0V
- Connector Type: PH2.0-4P
- Interface Protocol: I2C(IIC)
- Interface Signal Level: High 3.3V, Low 0V
- Dimension: 42 * 32mm / 1.65 * 1.26 inch
Controller Side(Non-isolation Side)
- Supply Voltage: 5.0 ± 0.15V
- No-load Current: 15mA(TYP)
Module Side(Isolation Side)
- Output Voltage: 5.0 ± 0.15V
- Output Current: 150mA(MAX)
DOCUMENTS
SHIPPING LIST
- Gravity: Digital I2C Signal Isolator x1
- Double PH2.0-4P Cable x1
- Gravity-4P I2C/ UART Sensor Cable x1
- XH2.54-4Pin Header x2
相關商品
-
Grove – I2C 16 x 2 LCD 液晶模組 黃底黑字 seeed原廠
0 滿分 5 分NT$286NT$240 未稅加入購物車Quick View -
Grove – I2C Touch Sensor 電容式觸摸感測器 I2C 觸摸開關感應器 seeed原廠
0 滿分 5 分I2C 觸摸感測器使用飛思卡爾MPR121晶片,它可以感應觸碰和人的手指的接近。這個感應器包括兩部分——一個觸碰感應控制器和4個感應片。把感應片插到控制器上,就可以開始使用了。
NT$819NT$400 未稅加入購物車Quick View -
I2C_LCD (With universal Grove cable) 圖形文字顯示模組 seeed原廠
0 滿分 5 分I2C LCD是一個易於使用的顯示模塊,它可以使顯示器更加容易。使用它可以減少顯示開發的難度,從而使製造商可以專注於工作的核心。
NT$800NT$700 未稅加入購物車Quick View -
IIC / I2C 1602 LCD 藍色背光液晶模組 藍底白字
0 滿分 5 分採用優質1602液晶螢幕,藍底白字,顯示清楚,I2C匯流排控制,只佔用兩個IO口,背光燈可調,可以用跳線控制,也可以透過程式控制亮度,螢幕顯示對比度可調,5V電壓供電,I2C位址0x27,適用於arduino平台
NT$171NT$100 未稅加入購物車Quick View -
加入購物車Quick View
HC-05 串口藍牙模組 (帶底板) 主機/從機可設定 / 帶底板,附 Arduino 範例
0 滿分 5 分請勿將電源接到信號腳上,會直接燒壞模組!
藍牙透傳模組只有4個AT指令,分別是測試通訊,改名稱,改串列傳輸速率,改配對密碼,AT指令必須從TXD,RXD信號腳設置,不能通過藍牙通道設置。發送AT指令的設備可以是各種類型的MCU(比如51,avr,pic,msp430,arm等),也可以是電腦通過串口(PC串口接MAX232以後或者USB轉串口)發送。
加入購物車Quick View -
Fermion:LWLP5000 差壓感測器±500pa DFRobot原廠
0 滿分 5 分NT$1,524NT$1,420 未稅加入購物車Quick View -
加入購物車Quick View
2路電平轉換模組帶隔離 2-Channel Level Converter (12V to 5V) DFRobot原廠
0 滿分 5 分加入購物車Quick View -
加入購物車Quick View
Grove – 0.96″ OLED 顯示模組 (SSD1315) 黑底白字 seeed原廠
0 滿分 5 分加入購物車Quick View -
GY-SHT31-D 數位型 i2c 通訊 , 溫濕度感測器模組
0 滿分 5 分GY-SHT31-D 數位型 i2c 通訊 , 溫濕度感測器模組
Sensiron Temperature/Humidity sensors are some of the finest & highest-accuracy devices you can get. And, finally we have some that have a true I2C interface for easy reading. The SHT31-D sensor has an excellent ±2% relative humidity and ±0.3°C accuracy for most uses.
NT$410NT$305 未稅加入購物車Quick View -
1.3吋OLED 液晶屏顯示模組 黑底藍字 I2C OLED模塊!只需4個引腳
0 滿分 5 分OLED模组4個引腳排列順序有(GND VCC SCL SDA) / (VCC GND SCL SDA)兩種,隨機出貨若有要指定請下單時備註腳位順序。
NT$286NT$171 未稅加入購物車Quick View