





溶解氧感測器 V2 溶解氧含量 水電導率感測器 液體檢測 水質監測 相容Arduino Gravity
NT$3,143 NT$2,619 未稅
Gravity:模擬電導率計V2專門用於測量水溶液的電導率值,評估水質狀況,常用於水培、水產養殖、環境水檢測等領域。
產品配合主控板(如Arduino)與配套的軟件庫,就可迅速搭建出一套電導率檢測儀,即插即用,無需焊接。
尚有庫存
- 商品說明
商品說明
Arduino Gravity: 溶解氧感測器 V2 溶解氧含量 水電導率感測器 液體檢測 水質監測 相容Arduino
溶解氧感測器 V2 專門用於測量水溶液的電導率 。評估水質狀況,常用於水培、水產養殖、環境水檢測等領域。V2電導率儀為V1的升級版,大大提高了用戶體驗和數據精度。它支持3~5v寬電壓輸入,並兼容5V和3.3V主控板; 由硬件濾波的輸出信號具有低抖動; 激勵源採用交流信號,有效降低極化效應,提高精度,延長探頭壽命; 該軟件庫採用兩點校準方法,可以自動識別標準緩衝解決方案,因此簡單方便。
有了這個產品,主控板(如Arduino)和軟件庫,可以快速建立電導率儀,即插即用,無需焊接。DFRobot提供各種水質傳感器產品,尺寸與接口統一,滿足各類水質檢測的需求,也適合搭建多參數水質檢測儀。
電導率是電阻率的倒數,與物質傳送電流能力的大小有關,在液體中常以電阻的倒數電導來衡量其導電能力的大小。水的電導是衡量水質的一個重要指標,它能反映出水中存在的電解質的程度。
- 本產品配套的電極為實驗室級電極,請勿長時間放在液體中測量,否則會縮短電極的使用壽命。
- 本產品配套的電極的鉑金片表面附著有鉑黑層,應避免任何物體與其觸碰,只能用蒸餾水沖洗,否則會損傷鉑黑層,導致電極測量不准確。
接線圖
注意:
特徵
- 3.0~5.0V寬電壓輸入
- 硬件濾波輸出信號,低抖動
- 交流激勵源,有效減少極化
- 重力連接器和BNC連接器,即插即用,無需焊接
- 軟件庫支持兩點校準,並自動識別標準緩衝解決方案,集成溫度補償算法
- 尺寸和連接器尺寸均勻,便於機械結構設計
應用
- 水質監測。
- 水產養殖。
- 水培和Aquaponic。
規格參數
- 信號轉換板(發射器)V2:
- 供電電壓:3.0~5.0V
- 輸出電壓:0~3.4V
- 電極接口:BNC
- 信號接口:PH2.0-3Pin
- 測量精度:±5% FS
- 板子尺寸:42mm*32mm
- 電導率電極:
- 電極類型:實驗室級電極
- 電極常數:1.0
- 支持檢測範圍:0~20ms/cm
- 推薦檢測範圍:1~15ms/cm
- 溫度範圍:0~40℃
- 電極壽命:>0.5年(實際壽命與使用頻率、場景有關)
- 線纜長度:100cm
出貨清單
- 電導率探頭(K = 1,實驗室級)x1
- 信號轉換板(發射器)V2 x1
- 標準緩衝溶液1413us / cm x2
- 標準緩衝溶液12.88ms / cm x2
- 重力模擬傳感器連接線 x1
- 防水墊片x2
- BNC連接器x1的螺帽
- M3 * 10尼龍柱x4
- M3 * 5螺絲x8
Documents
=========================================================
Gravity: Analog Electrical Conductivity Sensor /Meter V2 (K=1)
DFRobot Gravity: analog electrical conductivity meter V2 is specially used to measure the electrical conductivity of aqueous solution, and then to evaluate the water quality, which is often used in water culture, aquaculture, environmental water detectionand other fields. You may also check Liquid Sensor Selection Guide to get better familar with our liquid sensor series.
This product, as an upgraded version of electrical conductivity meter V1, greatly improves the user experience and data precision. It supports 3~5v wide voltage input, and is compatible with 5V and 3.3V main control board; The output signal filtered by hardware has low jitters; The excitation source adopts AC signal, which effectively reduces the polarization effect, improves the precision and prolongs the life of the probe; The software library uses two-point calibration method, and can automatically identify standard buffer solution, so simple and convenient.
With this product, main control board (such as Arduino) and the software library, you can quickly build an electrical conductivity meter, plug and play, no welding. DFRobot provides a variety of water quality sensor products, uniform size and interface, not only meet the needs of various water quality testing, but also suitable for the DIY of multi-parameter water quality tester.
Conductivity is the reciprocal of the resistance, which is related to the ability of the material to carry the current. In the liquid, the reciprocal of the resistance, the conductivity, is the measure of its ability to conduct electricity. Conductivity is an important parameter of water quality. It can reflect the extent of electrolytes present in water.
In order to ensure the measurement accuracy, it is strongly recommended to add a temperature sensor to measure the temperature, and achieve automatic temperature compensation. DS18B20 waterproof temperature sensor can also be used.
1.The probe is a laboratory-grade probe. Do not immerse in liquid for a long time. Otherwise this will shorten the life of the probe.
2.Platinum black layer is attached to the surface of the sheet metal in the probe.It should avoid any object touching it. It can only be washed with distilled water, otherwise the platinum black layer will be damaged, resulting in inaccurate measurement.
FEATURES
- 3.0~5.0V wide voltage input
- Hardware filtered output signal, low jitter
- AC excitation source, effectively reduce polarization
- Gravity connector and BNC connector, plug and play, no welding
- Software library supports two-point calibration, and automatically identifies standard buffer solution, integrates temperature compensation algorithm
- Uniform size and connector, convenient for the design of mechanical structures
APPLICATIONS
- Water quality monitoring.
- Aquaculture.
- Hydroponic & Aquaponic.
SPECIFICATION
Signal Conversion Board (Transmitter) V2
- Supply Voltage: 3.0~5.0V
- Output Voltage: 0~3.4V
- Probe Connector: BNC
- Signal Connector: PH2.0-3Pin
- Measurement Accuracy: ±5% F.S.
- Board size: 42mm*32mm/1.65in*1.26in
Electrical Conductivity Probe
- Probe Type: Laboratory Grade
- Cell Constant: 1.0
- Support Detection Range: 0~20ms/cm
- Recommended Detection Range: 1~15ms/cm
- Temperature Range: 0~40°C
- Probe Life: >0.5 year (depending on frequency of use)
- Cable Length: 100cm
DOCUMENTS
SHIPPING LIST
- Electrical Conductivity Probe(K=1,Laboratory Grade) x1
- Signal Conversion Board (Transmitter) V2 x1
- Standard Buffer Solution 1413us/cm x2
- Standard Buffer Solution 12.88ms/cm x2
- Gravity Analog Sensor Cable x1
- Waterproof Gasket x2
- Screw Cap for BNC Connector x1
- M3 * 10 nylon pillar x4
- M3 * 5 screw x8
相關商品
-
Water Sensor 水位感測器
0 滿分 5 分Water Sensor水位感測器是一款簡單易用、性價比較高的水位/水滴識別檢測傳感器,其是通過具有一系列的暴露的平行導線線跡測量其水滴/水量大小從而判斷水位。輕松完成水量到模擬信號的轉換,輸出的模擬值可以直接被Arduino開發板讀取,達到水位報警的功效。
NT$48NT$38 未稅加入購物車速覽 -
副廠 Esplora 遊戲機開發控制板 GamePad 採用原廠晶片支援Arduino
0 滿分 5 分Esplora 是 Leonardo 的增強版,控制晶片依舊採用Leonardo用的Atmega32U4,可以直接控制USB與上位機的通信,模擬PC機的鍵盤和鼠標等外設。Esplora最突出的特性是增加了幾個內建的輸入設備和傳感器,還有幾個輸入輸出接口。
NT$848NT$790 未稅加入購物車速覽 -
感測器37件組 | 入門感測器學習Arduino教學套件/詳細Arduino Sensor 入門教材資料
0 滿分 5 分感測器37件組 | 感測器入門學習Arduino套件 |滿滿 2.4G 1CD 入門教材資料
最佳的感測器入門學習Arduino套件,讓您幾分鐘之內快速上手,不需四處奔波搜尋各種教學資料, 直接給給你最齊全的感測器零件組合與教學課程與範例程式,立刻體驗豐富有趣的Arduino創作世界。這款入門套件收錄了 Arduino 初學者最常應用到的感測器零件,以及介紹這 37 種感測器的使用教學與程式範例。
NT$1,333NT$1,143 未稅加入購物車速覽 -
FTDI Basic Breakout – 5V FT232RL晶片 SparkFun原廠
0 滿分 5 分NT$695NT$438 未稅加入購物車速覽 -
SAMD21 Mini Breakout SparkFun原廠
0 滿分 5 分NT$810NT$781 未稅加入購物車速覽 -
Teensy Arduino Shield Adapter (Teensy擴展板 相容於Arduino) SparkFun原廠
0 滿分 5 分Teensy是一款很簡易開發平臺,您可以將其結合Arduino, Teensy Arduino Shield擴展板提供了這樣的功能
NT$429NT$362 未稅加入購物車速覽 -
MEGA 感測器擴展板 V2.4 Arduino通用 Xbee 藍芽串口 SD卡座 DFRobot原廠
0 滿分 5 分NT$743NT$571 未稅加入購物車速覽 -
USB 9V升壓線 5V轉9V 升壓線 支援Arduino 行動電源升壓線
0 滿分 5 分讓您的 Arduino 專案不用擔心電壓不足的情況,透過行動電源或者一般 PC USB 升壓 9V 給 Arduino 外部供電, 您可以使用任何一種大容量的行動電源當呈給 Arduino 的電池供電,穩定的透過 Arduino 5.5×2.1 外部電源接口穩定供電。
NT$95NT$76 未稅加入購物車速覽 -
Relay Shield v3.0 繼電器擴充板支援Arduino單機片Seeed 原廠公司貨
0 滿分 5 分如果你發現Arduino的小電流限制了你的發揮,那麼Relay Shield將會幫到你。這款Relay Shield簡單易用,它允許你使用簡單的靜態繼電器來控制4路大功率設備(每路上至8Amps,35 Volts)。
每一路都配備有LED指示燈以指示繼電器的當前工作狀態。高性能端子的使用使得Relay Shield的使用更加安全和可靠。對於大功率的Arduino項目或者機器人應用,這款Realy Shield將是理想的選擇。
NT$762NT$619 未稅加入購物車速覽 -
開發板電源供應器 變壓器 外接電源 100V~240VAC轉 9V/1A 穩壓電路
0 滿分 5 分輸入電壓:AC(交流)100V-240V 50-60Hz
輸出電壓:DC(直流)9V
額定輸出電流:1A
輸出DC介面:外徑5.5mm內徑2.1mm
插頭極性:內正外負
產品優勢:採用全新線路板以及元器件NT$114NT$81 未稅加入購物車速覽