Gravity: Analog Turbidity Sensor 水濁度感測器 水質檢測 養殖環境監測 For Arduino DFRobot原廠
NT$648 NT$500 未稅
濁度感測器利用光學原理,通過測量溶液中的透光率和散射率來綜合判斷溶液濁度情況,從而達到檢測水質的目的。
尚有庫存
- 商品說明
商品說明
Gravity: Analog Turbidity Sensor For Arduino 水濁度感測器 水質 養殖環境監測
濁度感測器利用光學原理,通過測量溶液中的透光率和散射率來綜合判斷溶液濁度情況,從而達到檢測水質的目的。
感測器內部是一個紅外線對管,當光線穿過一定量的水時,光線的透過量取決於該水的污濁程度,水越污濁,透過的光就越少。
感測器可以用於洗衣機、洗碗機,魚缸等產品的水污濁程度的測量。通過測量水的污濁程度來判斷溶液的潔淨程度,確定換水時間,達到減少能耗和節約用水的目的。也可以用於河流,污水的測量,澄清池檢測和水質研究等等。
感測器提供類比信號和數位信號兩種輸出模式。相容Gravity 3-Pin介面,可直連Arduino擴展版,免除二次接線的麻煩,簡單實用。
注意:感測器探頭頂端不防水,請勿浸沒使用,切記!
規格
- 工作電壓:5VDC
- 工作電流:40mA (MAX)
- 回應時間:<500ms
- 絕緣電阻:100MΩ (Min)
- 模擬量輸出:0-4.5V
- 數位量輸出:高/低電平信號(可以通過調節電位器選擇對應閾值)
- 操作溫度:-30℃~80℃
- 存儲溫度:-10℃~80℃
- 重量:30g
- 轉接板尺寸:38mm*28mm*10mm
接線圖
出貨清單
- Turbidity sensor adapter x1
- Turbidity sensor probe x1
- Turbidity sensor cable x1
- Gravity analog sensor cable x1
Documents
=========================================================
Gravity: Analog Turbidity Sensor For Arduino
The arduino turbidity sensor detects water quality by measuring level of turbidity. It is able to detect suspended particles in water by measuring the light transmittance and scattering rate which changes with the amount of total suspended solids (TSS) in water. As the TTS increases, the liquid turbidity level increases. You may also check Liquid Sensor Selection Guide to get better familar with our liquid sensor series.
This arduino turbidity sensor have both analog and digital signal output modes. You can select the mode according to the MCU as threshold is adjustable in digital signal mode.
Turbidity sensors can be used in measurement of water quality in rivers and streams, wastewater and effluent measurements, sediment transport research and laboratory measurements.
SPECIFICATION
- Operating Voltage: 5V DC
- Operating Current: 40mA (MAX)
- Response Time: <500ms
- Insulation Resistance: 100M (Min)
- Output Method:Analog
- Analog output: 0-4.5V
- Digital Output: High/Low level signal (you can adjust the threshold value by adjusting the potentiometer)
- Operating Temperature: 5℃~90 ℃
- Storage Temperature: -10℃~90℃
- Weight: 30g
- Adapter Dimensions: 38mm*28mm*10mm/1.5inches *1.1inches*0.4inches
DOCUMENTS
SHIPPING LIST
- Turbidity sensor adapter x1
- Turbidity sensor probe x1
- Turbidity sensor cable x1
- Gravity analog sensor cable x1
相關商品
-
Grove – Relay 繼電器模組 ( 峰值電壓能力250V 10安培) 支援 Arduino 與 Raspberry Pi seeed原廠
0 滿分 5 分繼電器是數位電路常用的控制開關元件,可用於控制更高的電壓和電流。設置為高電位時,指示燈會亮,繼電器ON。
NT$143NT$120 未稅加入購物車Quick View -
Grove – I2C Touch Sensor 電容式觸摸感測器 I2C 觸摸開關感應器 seeed原廠
0 滿分 5 分I2C 觸摸感測器使用飛思卡爾MPR121晶片,它可以感應觸碰和人的手指的接近。這個感應器包括兩部分——一個觸碰感應控制器和4個感應片。把感應片插到控制器上,就可以開始使用了。
NT$819NT$400 未稅加入購物車Quick View -
Grove – Air quality sensor v1.3 空氣品質感測器模組 seeed原廠
0 滿分 5 分主要可以監測的氣體是一氧化碳,醇,丙酮,稀釋劑,甲醛等輕微毒性氣體。本模組兼容 5V和3.3V電源。
NT$457NT$300 未稅加入購物車Quick View -
Grove – Alcohol Sensor 酒精感測器 seeed原廠
0 滿分 5 分酒精感測器(傳感器)為酒精專用檢測半導體傳感器。它具有良好的靈敏度和回應速度快的特性,本模組適用用於開發便攜式酒精檢測系統。
NT$286NT$220 未稅加入購物車Quick View -
Grove – PIR Motion Sensor 紅外線人體移動探測感測器 seeed原廠
0 滿分 5 分這是一個極易使用的紅外線 PIR人體運動探測感測器。通過這個感測器,你可以使你的作品對運動,例如人類的運動作出互動。只要將其接到Grove – Base Shield上,並且下載程序,當有人走入它的探測範圍時,PIR運動探測傳感器就會在它的SIG腳上輸出一個HIGH信號。
NT$333NT$260 未稅加入購物車Quick View -
加入購物車Quick View
單片機TTL轉RS485模組 485轉串口UART電平互轉 硬體自動控制流向
0 滿分 5 分加入購物車Quick View -
Fermion:LWLP5000 差壓感測器±500pa DFRobot原廠
0 滿分 5 分NT$1,524NT$1,420 未稅加入購物車Quick View -
ESP8266 串口 WIFI模組 遠距離 無線模組 ESP-07
0 滿分 5 分半孔貼片工藝,所有IO引出,帶金屬屏蔽殼,可過FCC CE認證,可外接IPX天線,也可用內置陶瓷天線
NT$143NT$100 未稅加入購物車Quick View -
Grove – 3-Axis Analog Accelerometer 3軸加速度計 seeed原廠
0 滿分 5 分ADXL335 是一款小巧,薄型,低功耗,完整的3軸加速度計,具有信號調理電壓輸出。 該產品可測量加速度,最小滿量程範圍為±3 g。
NT$476NT$380 未稅加入購物車Quick View -
Grove – Gas Sensor(MQ5) 氣體感測器 Seeed原廠
0 滿分 5 分可檢測液化石油氣,天然氣,城鎮煤氣等。基於其快速響應時間,測量可以盡快進行。且其靈敏度也可以通過電位器來進行調節。
NT$276NT$220 未稅加入購物車Quick View