- 商品說明
商品說明
Gravity: Heart Rate Monitor Sensor 超小型心率 血氧飽和值 監測傳感器/感測器 for Arduino
DFRobot心率傳感器是一款拇指大小的心率監測儀,專為Arduino微控制器設計。
它包括一個Gravity接口,可輕鬆實現即插即用連接。
該傳感器是基於PPG(PhotoPlethysmoGraphy)技術開發的脈衝傳感器。這是一種簡單且低成本的光學技術,可用於檢測組織微血管床中的血容量變化。
根據該理論,相對容易檢測心動週期的脈動分量。
傳感器有兩個孔,可用於連接皮帶。您可以將手指,手腕,耳垂或其他與皮膚接觸的區域包裹起來。
心臟傳感器有兩種信號輸出模式:模擬脈沖模式和數字方波模式。您可以使用撥號開關更改其輸出模式。有許多用戶場景,包括教育,體育或製造商/互動項目!
-
請注意:本產品不是醫療器材,不能用作此類產品或作為其附件使用,也不能用於診斷或治療任何疾病。
開始之前
打開包裝盒後,您可以在包裝內找到黑帶。將其穿過傳感器的孔,如照片中所示。然後你可以將它附在你的手指(建議),手腕或任何其他暴露血管的地方。請勿將皮帶太緊或太鬆,否則讀數可能不穩定。除此之外,在測試過程中,你應該穩定你的手指,不要移動太多,否則讀數會很差。
基於物聯網的心率監測系統是向Blynk應用程序發送脈率並從任何地方監測它的一個非常基礎的項目。
引腳說明
接線圖
規格
- 輸入電壓(Vin):3.3 – 6V(推薦5V)
- 輸出電壓:0 – Vin(模擬),0 / Vin(數字)
- 工作電流:<10mA
- 尺寸:28 x 24(mm),1.102“x 0.945”(in)
- 接口類型:PH2.0-3P
出貨清單
- 心率感測器 x1
- 手腕帶 x1
- PH2.0-3P電線 x1
-
請注意:
1.本產品不是醫療器械,不能用作此類產品或作為其附件使用,也不能用於診斷或治療任何疾病。
2.此為靜態心率傳感器,測量時請勿隨意移動,也勿按壓過緊。
Documents
=========================================================
Gravity: Heart Rate Monitor Sensor for Arduino
The DFRobot heart rate sensor is a thumb-sized heart rate monitor designed for Arduino microcontrollers.
This heart rate monitor sensor is a pulse sensor which is developed based on PPG techniques. This is a simple and low-cost optical technique that can be used to detect blood volume changing in the microvascular bed of tissues. It is relatively easy to detect the pulsatile component of the cardiac cycle according to this theory.
The sensor has two holes that you can use to attach to your belt. You can wrap on your finger, wrist, earlobe or other areas where it has contact with your skin.
A Gravity Interface is adapted to allow plug&play to ease the barrier of usage. The IO sensor shield is the best option to connect this heart rate sensor with your Arduino or other microcontrollers. Besides, this sensor can also be compatible with Raspberry Pi, intel edison, joule and curie by means of 3.3V Input Voltage.
NOTE:
1. This product is NOT a professional medical device and should not be used to diagnose or treat medical conditions.
2. This sensor is designed to work when the user is not moving. If used while moving it will give inaccurate results.
SPECIFICATION
- Input Voltage (Vin): 3.3 – 6V (5V recommended)
- Output Voltage: 0 – Vin (Analog), 0/ Vin (Digital)
- Operating current: <10mA
- Dimension: 28 x 24(mm), 1.102″ x 0.945″(in)
- Interface Type: PH2.0-3P
DOCUMENTS
SHIPPING LIST
- Heart Rate Monitor Sensor For Arduino x1
- Wrist belt x1
- PH2.0-3P cable x1
相關商品
-
加入購物車Quick View
Gravity: I2C 非接觸式紅外線溫度感測器 MLX90614 for Arduino DFRobot原廠
0 滿分 5 分加入購物車Quick View -
加入購物車Quick View
單片機TTL轉RS485模組 485轉串口UART電平互轉 硬體自動控制流向
0 滿分 5 分加入購物車Quick View -
Grove – Infrared Temperature Sensor 紅外線 溫度感測器模組 seeed原廠
0 滿分 5 分紅外溫度傳感器通過接收物體發出的紅外線來測量其溫度。
NT$457NT$380 未稅加入購物車Quick View -
5路循跡感測器 五路紅外線尋跡感測器 帶碰撞、距離檢測功能
0 滿分 5 分NT$190NT$152 未稅加入購物車Quick View -
電流轉電壓模組 0/4-20mA 轉 0-3.3V、5V、10V 電壓變送器 信號轉換調理
0 滿分 5 分在電路信號傳輸的過程中電壓信號會隨著傳輸距離的增加而變弱,採用電流傳輸可以避免信號的變弱。
本模組用於電流信號傳輸末端,將信號轉換成電壓信號供單片機檢測。
電流輸入支援4-20Ma、0-20mA,電壓輸出支援0-3.3V、0-5V、0-10V
NT$190NT$114 未稅加入購物車Quick View -
Fermion:LWLP5000 差壓感測器±500pa DFRobot原廠
0 滿分 5 分NT$1,524NT$1,420 未稅加入購物車Quick View -
GY-530 VL53LDK 激光測距感測器 ToF測距 飛行時間測距
0 滿分 5 分鐳射測距智慧感測器,新的智慧感測器基於成功的FlightSense™技術,實現更快、更遠、更精確的測距功能,大幅提升手機和平板電腦的拍照性能,為智慧型機器人、用戶檢測、無人機、物聯網和穿戴式裝置市場開拓新的應用機會
NT$362NT$190 未稅加入購物車Quick View -
加入購物車Quick View
Force Sensitive Resistor – FSR400 Small 電阻式壓力感測器 SparkFun原廠
0 滿分 5 分直徑為0.16“(4 mm)的有源感應區域,Interlink Electronics的FSR會根據傳感區域的壓力而改變其阻力,力越強,電阻越小,當沒有壓力應用於FSR,其電阻將大於1MΩ,全壓施加電阻為2.5kΩ。
加入購物車Quick View -
加入購物車Quick View
Grove – Rotary Angle Sensor 旋轉角度電位器模組 seeed原廠
0 滿分 5 分加入購物車Quick View -
加入購物車Quick View
Grove – Multichannel Gas Sensor v2 多通道有害氣體感測器 seeed原廠
0 滿分 5 分加入購物車Quick View